background image

English 

Mounting directions of suction grille.

3-3 

Select one of the following mounting directions of the suction grille 
on the panel.

Piping

Piping

Drain 
socket

Dust 
collection 
inlet

Drain 
socket

Suction 
grille

PREPARATIONS FOR PANEL

4. 

Note

Perform all the required work in 

• 

“4. PREPARATIONS FOR 

PANEL”

 with the panel kept in the packing material (on the 

bottom side).
Do not put the panel downward or upright or leave the panel on 

• 

protruding parts.
Otherwise, scratch damage to the surface of the panel may 
result.

Removal of suction grille from panel, protective 

4-1 

corrugated cardboard, and set of accessories.

Press the knobs of the suction grille and lift up the knobs.

(1) 

Decoration panel

Knobs

Packing material 
(bottom)

Suction grille

Open the suction grille to an angle of approximately 45° and 

(2) 

remove the suction grille from the panel.

45°

Take out the protective corrugated cardboard.

(3) 

Take out the protective corrugated cardboard (on top of the 
panel) together with the accessories attached to the backside 
of the protective corrugated cardboard.

Protective corrugated 
cardboard (top) 
(The accessories are 
on the backside.)

Protective corrugated 
cardboard (bottom)

Note

Do not impose force on the swing fl ap, brush unit, or air fi lter 
when handling the panel.

Panel

Brush unit

Air filter

Swing flap

Removal of decoration corner covers.

4-2 

Panel

Decoration corner cover

Decoration corner cover

Decoration 
corner cover

Decoration corner 
cover (with display)

Raise and remove the decoration corner cover (with the 

(1) 

display) in the direction of the arrow.

Note

Do not impose force on the lead wires.

Operation/filter cleaning 

Remove the screws on the backside of the decoration corner 

(2) 

cover (with the display), open the cover, and remove the 
connector attached to the front end of the lead wires from the 
PCB.

Cover

Connector

Lead wires

PCB

3

1

Screw

2

Decoration corner cover 
(with display)

Remove each of the remaining decoration corner covers (i.e., 

(3) 

three covers) in the direction of the arrow.

Panel

Decoration corner cover

Removal of dust box.

4-3 

Fixing knob of 
dust box and 
clasp

Dust box

Fixing knob of dust box

01_EN_3P257556-1.indd   3

01_EN_3P257556-1.indd   3

9/3/2009   4:04:45 PM

9/3/2009   4:04:45 PM

Summary of Contents for BYCQ140CGW1













Reviews: