manualshive.com logo in svg

Daikin Altherma EHYHBH05A Series, Installer'S Reference Manual

Share
Download
Daikin Altherma EHYHBH05A Series Installer'S Reference Manual Download Page 57

7

 | 

Unit installation

Installer reference guide

57

08CA + EHY EHYHBH/X08A + EHYKOMB33AA
Daikin Altherma hybrid heat pump
4P355634-1G – 2022.09

Typical workflow

Mounting the outdoor unit typically consists of the following stages:

1

Providing the installation structure.

2

Installing the outdoor unit.

3

Providing drainage.

4

Protecting the unit against snow and wind by installing a snow cover and baffle
plates. See 

"7.1 Preparing the installation site"

 [

4

 48].

7.3.2 Precautions when mounting the outdoor unit

INFORMATION

Also read the precautions and requirements in the following chapters:

▪

"3 General safety precautions"

 [

4

 12]

▪

"7.1 Preparing the installation site"

 [

4

 48]

7.3.3 To provide the installation structure

Check  the  strength  and  level  of  the  installation  ground  so  that  the  unit  will  not
cause any operating vibration or noise.

Fix  the  unit  securely  by  means  of  foundation  bolts  in  accordance  with  the
foundation drawing.

If  the  unit  is  installed  directly  on  the  floor,  prepare  4  sets  of  M8  or  M10  anchor
bolts, nuts and washers (field supply) as follows:

INFORMATION

The maximum height of the upper protruding part of the bolts is 15 mm.

283

580

<100

(mm)

<100

>300

In  any  case,  provide  at  least  300  mm  of  free  space  below  the  unit.  Additionally,
make  sure  the  unit  is  positioned  at  least  100  mm  above  the  maximum  expected
level of snow. In this case, it is recommended to construct a pedestal, and on this
pedestal install the EKFT008CA option kit.

Summary of Contents for Altherma EHYHBH05A Series









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands