Daihen OTC ARXIS pulse P403L, Owner'S Manual

Page: 87 / 188

S
ETTING
W
ELDING
JOB
W
ELDING
C
ONDITION
C
HAPTER
6
85
Chapter 6 W
elding Condition
<Relationship of wire diameter and welding current at aluminum welding (Reference)>
DC WAVE
PULSE
MAG (18 % CO
2
)
(*1-1)
Fe 0.8/1.0/1.2 0.8/1.0/1.2/1.6 Manual/Auto. -
MAG (10 % CO
2
)
(*1-2)
Fe 0.8/1.0/1.2 0.8/1.0/1.2 Manual/Auto. -
MAG (2 % O
2
)
(*1-3)
CrNi 0.8/1.0/1.2 0.8/1.0/1.2/1.6 Manual/Auto. -
Cr 18 0.8/1.0/1.2 0.8/1.0/1.2 Manual/Auto. -
MAG (2.5 % CO
2
)
(*1-4)
CrNi 0.8/1.0/1.2 0.8/1.0/1.2/1.6 Manual/Auto. -
Cr 18 0.8/1.0/1.2 0.8/1.0/1.2 Manual/Auto. -
MIG (100 % Ar)
(*1-5)
Al/99 1.2/1.6 1.2/1.6 Manual/Auto. -
Al/Mg 1.0/1.2/1.6 1.0/1.2/1.6 Manual/Auto. -
Al/Si 1.0/1.2 1.0/1.2 Manual/Auto. -
MS-MIG (*4)
MIG (100 % Ar)
(*1-5)
Al/Mg 1.6 1.6 Manual/Auto. -
DC TIG - - - - - -
MMA - - - - - -
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those with the
following mixing ratios is used.
*1-1: MAG gas: Argon (Ar) 82 % + Carbon dioxide (CO
2
) 18 %
*1-2: MAG gas: Argon (Ar) 90 % + Carbon dioxide (CO
2
) 10 %
*1-3: MAG gas (stainless steel): Argon (Ar) 98 % + Oxygen (O
2
) 2 %
*1-4: MAG gas: Argon (Ar) 97.5 % + Carbon oxygen (CO
2
) 2.5 %
*1-5: MIG gas (Aluminum/Aluminum bronze/Silicon bronze): Argon (Ar) 100 %
*2: For "Manual" mode, the Manual mode or extended cable mode (extended mode of power cable) is available.
( 6.7.2.1
-
F1: Standard/Extended cable mode)
*3: In the welding of DC low spatter, the following devices are necessary for wire feeder and welding torch. For details, refer to the
instruction manual of each device.
• Wire feeder: CM-0401-D + K5952E00
• Welding torch: BTW450-30E or BTW450-40E
*4: This mode is suitable for welding hard aluminum medium-thickness plates.
Aluminum material
Wire diameter
(mm Φ )
Welding process
Range of stable welding power
source (A)
Al/Mg
(A5183, A5336 etc.)
1.0
DC 100 to 150
DC pulse/DC wave pulse 50 to 150
1.2
DC 120 to 250
DC pulse/DC wave pulse 50 to 230
1.6
DC 100 to 300
DC pulse/DC wave pulse 75 to 270
Al/Si or Al/99
(A4043 etc.)
1.2
DC 120 to 250
DC pulse/DC wave pulse 60 to 230
1.6
DC 150 to 350
DC pulse/DC wave pulse 100 to 270
WELDING
PROCESS
GAS (*1)
WIRE
MATERIALS
WIRE DIA. (mm)
Manual/Auto.
Penetration
adjustment
ARXIS WB-P403L ARXIS WB-P503L