Daihen OTC ARXIS pulse P403L, Owner'S Manual

Page: 69 / 188

L
IST OF
W
ELDING
JOB
W
ELDING
C
ONDITION
C
HAPTER
6
67
Chapter 6 W
elding Condition
F64
L pulse peak time fine
adjustment
-1.5 to 1.5 0.0 (ms)
Sets the adjustment value of pulse peak time at the
LOW side in pulse welding.
○
F65 L-base current fine adjustment -60 to 60 0 (A)
Sets the adjustment value of base current at the LOW
side in pulse welding.
○
F66
Feeding amplitude ratio
adjustment
0 to 100 50 (%)
Sets the feeding amplitude ratio of wire feeder speed in
wave pulse welding.
○
F67
Setting change of current value
(start condition, crater
condition)
OFF/ON OFF
When "4T" is selected, sets the current value of the start
condition and crater condition in the percentage based
on the current value of the welding condition.
OFF: invalid
ON: settable with percentage
○
F68
Setting of current value (start
condition)
10 to 300 100 (%)
Sets the current value of the start condition in the
percentage based on the current value of the welding
condition.
○
F69
Setting of current value (crater
condition)
10 to 300 100 (%)
Sets the current value of the crater condition in the
percentage based on the current value of the welding
condition.
○
F70
Upper limit setting for analog
remote control
20 to 400 (*1) 400 (A) Sets the upper limit (the value when the knob is turned
clockwise all the way) of the welding current adjustable
by the analog remote control (optional accessory).
-
20 to 550 (*2) 550 (A)
F71 Interval function OFF/ON OFF
This function repeats arc ON/OFF to control the heat
input.
○
F72 Interval function Arc ON time 0.20 to 9.99 1.00 (s) Sets the Arc-ON time in the Interval function.
○
F73 Interval function Arc OFF time 0.20 to 9.99 1.00 (s) Sets the Arc-OFF time in the Interval function.
○
F74 No function OFF (fixed) OFF No functions are provided. -
F75 Wire inching initial speed 0 / 0.4 to 2.0 0.4 (m/min) Sets the inching speed for the first second. -
F76 Wire feeder select OFF / ON
ON
Allows to select the wire feeder to use.
OFF: CM-7403
ON: CM-0401-D
-
F77
Welding power source
identification numbers
1 to 999 1
Sets whether power source identification numbers of
Welding result control function.
-
F78
Prevention of unintended torch
switch operation
OFF/ON OFF
An error code is displayed when welding is not
performed for five seconds after the pre-flow.
-
F79
Switching of CAN
communication connection
device
0/1/2/3 1
Sets the connection device to be used for the CAN
communication.
0: Digital Remote Control Box
1: Digital panel (Attached to wire feeder) and Intelli
torch
2: Digital pull torch
3: Digital middle feeder
-
F80
Switching of CAN
communication speed
0/1/2/3 0
Sets the connection speed of the CAN connection.
0: 500 kbps
1: 1 Mbps
2: 125 kbps
3: 250 kbps
-
F81
Torch switch setting with TIG
mode
OFF/ON OFF
During TIG MODE, operating the torch switch can control
the welding start and end.
-
F82
Arc stabilization for DC pulse
welding
0 to 30 0
If DC pulse welding is unstable by using extended power
supply cable, set to larger value side with the longer
extended cable for arc stabilization.
-
F83
Adjustment of Arc length after
arc start
-20 to 10 0
Adjusts the arc length right after starting the welding
operation.
-
F84 Automatic pulse adjustment 0/1/2 0
Sets the pulse mode that has the pulse automatic
adjustment function.
0: Standard pulse mode
1: Pulse mode for automatic adjustment
2: Pulse mode for automatic adjustment; Fixing of
adjustment value
○
F85
Adjustment amount in
automatic pulse adjustment
-9.99 to 9.99 0
The currently retained adjustment amount of pulse
automatic adjustment can be checked. In addition, the
adjustment amount can be changed manually.
○
No. Function Name Setting range Initial value Explanation Memory