Daihen OTC ARXIS pulse P403L, Owner'S Manual

Page: 67 / 188

L
IST OF
W
ELDING
JOB
W
ELDING
C
ONDITION
C
HAPTER
6
65
Chapter 6 W
elding Condition
F19 Alarm setting switching OFF/ON OFF
Sets the output status when an error of the alarm level
is detected:
OFF: Ineffective
ON: Stops the output
-
F20
Low input voltage
detection level
260 to 400 320 (V) Adjusts the low primary input voltage detection level. -
F21 Maximum cooling fan operation OFF/ON OFF
Sets the operation mode of cooling fan:
OFF: Economical operation
ON: Rotates the fan at maximum speed at all time
-
F22 No function OFF (fixed) OFF No functions are provided. -
F23
Sleep mode
switching time
0 to 10 0
Sets the time until the welding power source enters into
sleep mode:
0: OFF
1 to 10: 1 min to 10 min
-
F24 Wire feeding speed setting OFF/ON OFF
Sets the criteria for welding condition:
OFF: based on current
ON: based on wire feeding speed
-
F25 External output 1 setting
0/4 0
Sets the functions of output terminal of the
programmable I/O.
-
F26 External output 2 setting
F27 External output 3 setting
F28 External output 4 setting
F29 External input 1 setting
0 to 7
0
Sets the functions of input terminal of the
programmable I/O.
-
F30 External input 2 setting 0
F31 External input 3 setting 0
F32 External input 4 setting 0
F33 Spatter suppression rate display - -
When F33 is selected, the spatter suppression ratio (%)
is displayed on the touch panel.
This function is not configurable.
-
F34
Automatic correction of low
spatter function
OFF/ON ON
Sets ON/OFF of the automatic correction function for
the low spatter function.
OFF: No automatic correction
ON: With automatic correction
○
F35
Saving the correction value of
low spatter function
OFF/ON OFF
Sets whether to save the automatic correction value of
the low spatter function at completion of welding.
OFF: Not to save
ON: To save until the next welding starts
○
F36 Spatter adjustment P1P
-100 to +100 0 Sets the control parameters for Spatter adjustment.
○
F37 Spatter adjustment P2P
F38 Arc voltage detection switching 0 to 2 0
Switches the position of arc voltage detection.
0: Standard
1: When directly detected at the base metal side
2: When using the straight-polarity (wire negative) wire
-
F39 Output current gain adjustment -10 to 10 0 (A) Adjusts the current output value. It can only be adjusted
in calibration mode.
This function is used when calibration of welding current
or voltage is needed.
-
F40
Fine adjustment of Output
current gain
-0.99 to 0.99 0.00 (A)
F41 Output voltage gain adjustment -1.0 to 1.0 0.0 (V) Adjusts the voltage output value. It can only be adjusted
in calibration mode.
This function is used when calibration of welding current
or voltage is needed.
-
F42
Fine adjustment of output
voltage gain
-0.09 to 0.09 0.00 (V)
F43 CAN ID 1 to 16 1
Sets CAN ID numbers to be used in the PC monitoring
system, etc.
-
F44
Reading welding JOB with
remote control
OFF/ON OFF
Sets whether to read "1" to "10" of the welding JOB
stored on the memory via the analog remote control:
OFF: Not to read
ON: Reads
-
F45 Special 2T OFF/ON OFF
Sets the start condition and crater condition as applied
for a fixed period of time regardless of the torch switch
operation:
OFF: Not applied
ON: Applied (Time set by F46 and F47 is applied)
○
F46 Special 2T start time 0.0 to 10.0 0.0 (s)
Sets start time in the Special 2T.
(available when "ON" is selected in F45)
○
No. Function Name Setting range Initial value Explanation Memory