manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Switch Port Commands 

49 

 

config port_security 

Purpose 

Used to configure port lock settings. 

Syntax 

config port_security 

<portlist>/all  

admin_state [enabled/disaled] 

max_learning_addr <1-10> 

lock_address_mode 
[DeleteOnTimout/DeleteOnReset] 

Description 

This command allows for the configuration of the 
port  lock  security  feature.    Only  the  ports  listed 
in the <portlist> are effected. 

Parameters 

all 

−

  configure  port  lock  for  all  ports  on  the 

switch. 

portlist   

−

    specifies  a  range  of  ports  to  be 

configured.    The  port  list  is  specified  by  listing 
the  lowest  switch  number  and  the  beginning 
port  number  on  that  switch,  separated  by  a 
colon.    Then  highest  switch  number,  and  the 
highest port number of the range (also separeted 
by  a  colon)  are  specified.    The  beginning  and 
end  of  the  port  list  range  are  seperated  by  a 
dash.    For  example,  1:3  would  specify  switch 
number 1, port  3.    2:4  specifies  switch  number 
2,  port  4.    1:3-2:4  specifies  all  of  the  ports 
between switch 1, port 3 and switch 2, port 4 

−

 

in numerical order. 

admin_state  [enabled/disaled] 

–

  enable  or 

disable port lock for the listed ports. 

max_learning_addr <1-10> - use this to limit the 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

ABLE 6 Series Installation & Maintenance Instructions preview
6 Series
Brand: ABLE Pages: 5
hager EMN005 User Instructions preview
EMN005
Brand: hager Pages: 2
hager HIC4 A Series Quick Start preview
HIC4 A Series
Brand: hager Pages: 4
hager EGN100 Manual preview
EGN100
Brand: hager Pages: 2
Eaton RMQ-Titan M30 Series Instruction Leaflet preview
RMQ-Titan M30 Series
Brand: Eaton Pages: 4
Edge-Core AS7726-32X Quick Start Manual preview
AS7726-32X
Brand: Edge-Core Pages: 9
Kramer Sierra Video 1208V3S Specifications preview
Sierra Video 1208V3S
Brand: Kramer Pages: 2
REV Ritter RF102R Assembly And Operating Instructions Manual preview
RF102R
Brand: REV Ritter Pages: 15
Datavideo SE-2200 Instruction Manual preview
SE-2200
Brand: Datavideo Pages: 38
I-Tech JKP115-801e User Manual preview
JKP115-801e
Brand: I-Tech Pages: 39
Flowserve PMV WM Ultraswitch User Instructions preview
PMV WM Ultraswitch
Brand: Flowserve Pages: 16
B&B Electronics Elinx EIR418-2SFP-T User Manual preview
Elinx EIR418-2SFP-T
Brand: B&B Electronics Pages: 25
CIS CIS-CRS328-24P Quick Start Manual preview
CIS-CRS328-24P
Brand: CIS Pages: 3
Kramer VS-24xl User Manual preview
VS-24xl
Brand: Kramer Pages: 11
Evidence Cross-8/HPoE-10G User Manual preview
Cross-8/HPoE-10G
Brand: Evidence Pages: 321
Linksys EFAH05W User Manual preview
EFAH05W
Brand: Linksys Pages: 22
Triax TMS 5XX SE AQ-EU Series User Manual preview
TMS 5XX SE AQ-EU Series
Brand: Triax Pages: 6
ATEN Master View CS-102 User Manual preview
Master View CS-102
Brand: ATEN Pages: 11

Brands by name

Popular brands

Load more brands