D-Link DES-3326S - Switch - Stackable Page 274 Command Line Interface Reference Manual Download | Manualshive

Page: 274 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

274

RIP Commands

config rip rx_mode

Purpose

Used to configure RIP on the switch.

Syntax

config rip [ipif <ipif_name>/all] rx_mode
[[disable/v1_only]/[v2_only/v1_and_v2]
authentication [enabled/disabled]
<password>]

Description

This command is used to configure RIP on
the switch.

Parameters

<ipif_name>

−

The name of the IP interface.

all

−

Specifies all IP interfaces on the switch.

rx_mode

−

Determines how received RIP

packets will be interpreted

–

as RIP version

V1 only, V2 Only, or V1 and V2. This
entry specifies which version of the RIP
protocol will be used to receive RIP packets.
The Disabled entry prevents the reception of
RIP packets.
disable

−

Prevents the reception of RIP

packets.
v1_only

−

Specifies that only RIP v1 packets

will be accepted.
v2_only

−

Specifies that only RIP v2 packets

will be accepted.
v1_and_v2

−

Specifies that both RIP v1 and

v2 packets will be accepted.
authentication [enabled/disabled]

−

Enables

or disables authentication for RIP on the
switch.
<password>

−

Allows the specification of a

case-sensitive password.
state [enabled/disabled]

−

Allows RIP to be

enabled and disabled on the switch.

«
...
272
273
274
275
276
...
»

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

Brand: steute Pages: 20

Brand: Mellanox Technologies Pages: 12

Brand: Black Box Pages: 28

Brand: Pilz Pages: 8

Brand: cable matters Pages: 8

Brand: I-Tech Pages: 19

Brand: Linkskey Pages: 2

Brand: Black Box Pages: 50

SECURVIEW SV-7020

Brand: CrimeStopper Pages: 1

Brand: INDO Pages: 3

Brand: Smartwares Pages: 2

Brand: ATEN Pages: 178

Brand: Belkin Pages: 288

Brand: Digital Equipment Pages: 2

Brand: Veris Industries Pages: 2

Brand: AJAX Pages: 23

Brand: SEKURYX Pages: 15

Brand: Mini Gadgets Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands