D-Link DES-3326S - Switch - Stackable Page 145 Command Line Interface Reference Manual Download

Page: 145 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Forwarding Database Commands

145

show fdb

Purpose

Used to display the current unicast MAC
address forwarding database.

Syntax

show fdb {port <port>/vlan
<vlan_name>/mac_address
<macaddr>/static/aging_time}

Description

This command will display the current
contents of the switch

’

s forwarding

database.

Parameters

<port>

−

The port number corresponding to

the MAC destination address. The switch
will always forward traffic to the specified
device through this port.

<vlan_name>

−

The name of the VLAN on

which the MAC address resides.

−

The MAC address that will be

added to the forwarding table.

static

−

Displays the static MAC address

entries.

aging_time

−

Displays the aging time for the

MAC address forwarding database.

Restrictions

None.

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Search results

Summary of Contents for DES-3326S - Switch - Stackable

Reviews:

Related manuals for DES-3326S - Switch - Stackable

Brands by name

Popular brands

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326S - Switch - Stackable

Reviews:

Related manuals for DES-3326S - Switch - Stackable

Brands by name

Popular brands