manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

QOS Commands 

157 

 

config scheduling 

specify the maximum amount of time that 
packets will be delayed before being 
transmitted.  For a given priority queue, a 
value between 0 and 255 can be specified.  
This number is then multiplied by 16 
milliseconds to determine the maximum 
allowed latency.  For example, if 3 is 
specified for queue 0, the maximum latency 
allowed will be 3 X 16 ms = 48 ms.  When 
queue 0 has been waiting to transmit 
packets for longer than 48 ms, the currently 
transmitting priority queue is allowed to 
finish transmitting its current packet, and 
then queue 0 is allowed to begin 
transmitting its packets. 

Parameters 

<class_id> 

−

 Specifies which of the four 

priority queues the config scheduling 
command will be applied to.  The four 
priority queues are identified by number 

−

 

from 0 to 3 

−

 with queue 0 being the highest 

priority. 
max_packet <value 0-255> 

−

 Specifies the 

maximum number of packets the above 
specified priority queue will be allowed to 
transmit before allowing the next lowest 
priority queue to transmit its packets.  A 
value between 0 and 255 packets can be 
specified. 
max_latency <value 0-255> 

−

 Specifies the 

maximum amount of time the above 
specified priority queue will have to wait 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

Quick TMS Manual Of Installation And Use preview
TMS
Brand: Quick Pages: 28
Camozzi CSD Series Use And Maintenance Instructions preview
CSD Series
Brand: Camozzi Pages: 2
Eaton COOPER POWER SERIES Installation And Operation Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
tbs electronics RBS Series Manual preview
RBS Series
Brand: tbs electronics Pages: 2
Dexon DIMAX404 User Manual preview
DIMAX404
Brand: Dexon Pages: 31
IBM Storage Networking SAN128B-6 Installation, Service And User Manual preview
Storage Networking SAN128B-6
Brand: IBM Pages: 116
ATEN AS-251S User Manual preview
AS-251S
Brand: ATEN Pages: 4
Edge-Core ECS2000-18P Installation Manual preview
ECS2000-18P
Brand: Edge-Core Pages: 65
SLV 470819 Quick Installation Manual preview
470819
Brand: SLV Pages: 22
hager EG170 User Instruction preview
EG170
Brand: hager Pages: 2
I-Rocks IR-4650 Quick Installation Manual preview
IR-4650
Brand: I-Rocks Pages: 18
Campbell HUB-SDM8 Instruction Manual preview
HUB-SDM8
Brand: Campbell Pages: 10
Altinex 400-0226-003 User Manual preview
400-0226-003
Brand: Altinex Pages: 14
Pilz PSEN ma2.1p/ATEX Operating Instructions Manual preview
PSEN ma2.1p/ATEX
Brand: Pilz Pages: 8
Ocean Matrix OMX-07HMHM0004 Operation Manual preview
OMX-07HMHM0004
Brand: Ocean Matrix Pages: 6
Kramer VM-42 User Manual preview
VM-42
Brand: Kramer Pages: 8
NETGEAR GS308P Installation preview
GS308P
Brand: NETGEAR Pages: 2
JDS Uniphase SKB Series User Manual preview
SKB Series
Brand: JDS Uniphase Pages: 113

Brands by name

Popular brands

Load more brands