manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

54

 

Network Management Commands 

 

6 

N

ETWORK 

M

ANAGEMENT 

C

OMMANDS

 

The  network  management  commands  in  the  Command  Line 
Interface  (CLI)  are  listed  (along  with  the  appropriate  parameters) 
in the following table. 

The  DES-3326SR  supports  the  Simple  Network  Management 
Protocol  (SNMP)  versions  1,  2c,  and  3.    You  can  specifiy  which 
version of the SNMP  you  want  to  use  to  monitor  and  control  the 
switch.    The  three  versions  of  SNMP  vary  in  the  level  of  security 
provided between the management station and the network device.  
The  following  table  lists  the  security  features  of  the  three  SNMP 
versions: 

SNMP 
Version 

Authentication 
Method 

Description 

v1 

Community String 

Community String is used for 
authentication 

−

 NoAuthNoPriv 

v2c 

Community String 

Community String is used for 
authentication 

−

 NoAuthNoPriv 

v3 

Username 

Username is used for 
authentication 

−

 NoAuthNoPriv 

v3 

MD5 or SHA 

Authentication is based on the 
HMAC-MD5 or HMAC-SHA 
algorithms 

−

 AuthNoPriv 

v3 

MD5 DES or SHA 
DES 

Authentication is based on the 
HMAC-MD5 or HMAC-SHA 
algorithms 

−

 AuthPriv. 

DES 56-bit encryption is added 
based on the CBC-DES (DES-56) 
standard 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

Cisco Catalyst 3110G Getting Started Manual preview
Catalyst 3110G
Brand: Cisco Pages: 30
C&H Technologies M221 Specifications preview
M221
Brand: C&H Technologies Pages: 1
D-Box G3 Installation Manual preview
G3
Brand: D-Box Pages: 31
Murphy Temperature SWICHGAGE SPL Owner'S Manual preview
Temperature SWICHGAGE SPL
Brand: Murphy Pages: 4
ADDER GEMAV2GEM Installation And Use Manual preview
GEMAV2GEM
Brand: ADDER Pages: 46
Zektor HDA800 User Manual preview
HDA800
Brand: Zektor Pages: 65
N-Tron 100-POE4-MDR User Manual & Installation Manual preview
100-POE4-MDR
Brand: N-Tron Pages: 17
Samson 4747 Mounting And Operating Instructions preview
4747
Brand: Samson Pages: 64
LEGRAND HKRL20 Installation Manual preview
HKRL20
Brand: LEGRAND Pages: 30
Radio Systems HUB16-DC Technical Manual preview
HUB16-DC
Brand: Radio Systems Pages: 19
3onedata IES2008 Quick Installation Manual preview
IES2008
Brand: 3onedata Pages: 2
HDTV Supply HDTVCV0702HDS User Manual preview
HDTVCV0702HDS
Brand: HDTV Supply Pages: 15
cable matters 202046 Quick Start Manual preview
202046
Brand: cable matters Pages: 8
axing SPU 81-00 Operation Instructions preview
SPU 81-00
Brand: axing Pages: 4
I-Tech AVS801 User Manual preview
AVS801
Brand: I-Tech Pages: 22
Contemporary Controls CTRLink EISK8P-GT Installation Manual preview
CTRLink EISK8P-GT
Brand: Contemporary Controls Pages: 4
Accton Technology CheetaHub Power-3004E Quick Installation Manual preview
CheetaHub Power-3004E
Brand: Accton Technology Pages: 11
Gefen EXT-DPKVM-841 User Manual preview
EXT-DPKVM-841
Brand: Gefen Pages: 31

Brands by name

Popular brands

Load more brands