manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

VLAN Commands 

179 

 

 

config gvrp 

Purpose 

Used to configure GVRP on the switch. 

Syntax 

config gvrp [<portlist>/all] {state 
[enabled/disabled]/ingress_checking 
[enabled/disabled]} 

Description 

This command is used to configure the 
Group VLAN Registration Protocol on the 
switch. You can configure ingress checking, 
the sending and receiving of GVRP 
information, and the Port VLAN ID (PVID). 

Parameters 

<portlist> 

−

  A range of ports for which you 

want ingress checking. The port list is 
specified by listing the lowest switch 
number and the beginning port number on 
that switch, separated by a colon. Then 
highest switch number, and the highest 
port number of the range (also separated by 
a colon) are specified. The beginning and 
end of the port list range are separated by a 
dash. For example, 1:3 would specify switch 
number 1, port 3. 2:4 specifies switch 
number 2, port 4. 1:3-2:4 specifies all of the 
ports between switch 1, port 3 and switch 2, 
port 4 

−

 in numerical order. 

all 

−

  Specifies all of the ports on the switch. 

state [enabled/disabled] 

−

 Enables or 

disables GVRP for ports in port list. 
ingress_checking [enabled/disabled] 

−

 

Enables or disables ingress checking for the 
specified port list. 

Restrictions 

Only administrator-level users can issue 
this command. 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

N-Tron 100 Series User Manual & Installation Manual preview
100 Series
Brand: N-Tron Pages: 20
Hama 78499 Operating Instructions Manual preview
78499
Brand: Hama Pages: 10
Hama 11467 Operating Instruction preview
11467
Brand: Hama Pages: 14
socomec 95333400 Instruction Manual preview
95333400
Brand: socomec Pages: 43
SIIG AV-GM08G3-S1 Manual preview
AV-GM08G3-S1
Brand: SIIG Pages: 17
Ruby Tech Web-Smart GS-1208M Specifications preview
Web-Smart GS-1208M
Brand: Ruby Tech Pages: 2
Allen-Bradley Guard Master 440N-Z2NRS1A Installation Instructions preview
Guard Master 440N-Z2NRS1A
Brand: Allen-Bradley Pages: 4
3onedata ES2010G-2GS User Manual preview
ES2010G-2GS
Brand: 3onedata Pages: 4
KYLAND Technology SICOM3028GP Series Hardware Installation Manual preview
SICOM3028GP Series
Brand: KYLAND Technology Pages: 40
HDTV Supply HDTVMT0808140 User Manual preview
HDTVMT0808140
Brand: HDTV Supply Pages: 21
H3C S6812 Series Installation Manual preview
S6812 Series
Brand: H3C Pages: 77
A-Neuvideo ANI-88UHD Instruction Manual preview
ANI-88UHD
Brand: A-Neuvideo Pages: 16
G-Force Power Switch G0021 Instruction Manual preview
Power Switch G0021
Brand: G-Force Pages: 2
3Com 4200G PWR Getting Started Manual preview
4200G PWR
Brand: 3Com Pages: 104
Shinybow USA SB-5688CAK Instruction Manual preview
SB-5688CAK
Brand: Shinybow USA Pages: 32
Cambium Networks cnMatrix EX1K Basic Configuration Manual preview
cnMatrix EX1K
Brand: Cambium Networks Pages: 28
Cabletron Systems SmartSTACK 10 ELS10-26 Getting Started preview
SmartSTACK 10 ELS10-26
Brand: Cabletron Systems Pages: 18
SC&T HS42M-4K6G User Manual preview
HS42M-4K6G
Brand: SC&T Pages: 7

Brands by name

Popular brands

Load more brands