manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Network Management Commands 

81 

 

create snmp host 

• 

Message integrity 

−

 ensures that 

packets have not been tampered 
with in transit. 

• 

Authentication 

−

 determines that an 

SNMP message is from a valid 
source. 

• 

Encryption 

−

 scrambles the contents 

of messages to prevent it being seen 
by an unauthorized source. 

noauth_nopriv 

−

 Specifies that there 

will be no authorization and no 
encryption of packets sent between the 
switch and a remote SNMP manager. 

auth_nopriv 

−

 Specifies that 

authorization will be required, but 
there will be no encryption of packets 
sent between the switch and a remote 
SNMP manager. 

auth_priv 

−

 Specifies that authorization 

will be required, and that packets sent 
between the swtich and a remote SNMP 
manger will be encrypted. 

<auth_sting 32> 

−

 An alphanumeric 

string used to authorize a remote SNMP 
manager to access the switch

’

s SNMP 

agent. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

Kathrein EXR 221 Quick Start Manual preview
EXR 221
Brand: Kathrein Pages: 8
Nayar Systems Switch Manual preview
Switch
Brand: Nayar Systems Pages: 21
Kathrein EXD 1532 User Manual preview
EXD 1532
Brand: Kathrein Pages: 24
Kasia Switch Installation Manual preview
Switch
Brand: Kasia Pages: 5
WAGO 852-112/000-001 Manual preview
852-112/000-001
Brand: WAGO Pages: 30
Eaton SOL30 Series Instruction Leaflet preview
SOL30 Series
Brand: Eaton Pages: 4
SMC Networks PF2A7 Series Operation Manual preview
PF2A7 Series
Brand: SMC Networks Pages: 43
Edge-Core AS7326-56X Quick Start Manual preview
AS7326-56X
Brand: Edge-Core Pages: 9
KCC KTD-600 Series Manual preview
KTD-600 Series
Brand: KCC Pages: 6
Icy Box IB-AC618 Manual preview
IB-AC618
Brand: Icy Box Pages: 6
Quintech RFS 0702 Operation And Adjustment Procedure preview
RFS 0702
Brand: Quintech Pages: 2
N-Tron 302MC-XX Installation Manual preview
302MC-XX
Brand: N-Tron Pages: 16
Gefen ToolBox GTB-MHDMI1.3-441 User Manual preview
ToolBox GTB-MHDMI1.3-441
Brand: Gefen Pages: 25
PRO SIGNAL PSG3061 Quick Start Manual preview
PSG3061
Brand: PRO SIGNAL Pages: 4
Scion SC03.4101 Operation Manual preview
SC03.4101
Brand: Scion Pages: 8
Network Technologies SE-DVI-2 Installation And Operation Manual preview
SE-DVI-2
Brand: Network Technologies Pages: 7
Black Box LB9007A-SC-R Installation preview
LB9007A-SC-R
Brand: Black Box Pages: 2
NewStar NS-211KA User Manual preview
NS-211KA
Brand: NewStar Pages: 10

Brands by name

Popular brands

Load more brands