manualshive.com logo in svg

D-Link DES-3326S - Switch - Stackable, Command Line Interface Reference Manual

The D-Link DES-3326S Switch is a stackable network switch featuring advanced performance and flexibility. For a hassle-free setup and optimized usage, make sure to download the free Product Manual from our website. This comprehensive manual is available for download at manualshive.com to assist you in maximizing the potential of this outstanding switch.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Bootp Relay Commands 

261 

 

 

show bootp_relay 

Purpose 

Used  to  display  the  current  BOOTP  relay 
configuration. 

Syntax 

show bootp_relay {ipif <ipif_name>} 

Description 

This  command  will  display  the  current 
BOOTP  relay  configuration  for  the  switch,  or 
if  an  IP  interface  name  is  specified,  the 
BOOTP  relay  configuration  for  that  IP 
interface. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

for  which  you  what  to  display  the  current 
BOOTP relay configuration. 

Restrictions 

none. 

Example Usage: 

To display bootp relay status. 

   

DES-3326SR:4#show bootp_relay ipif System 
Command: show bootp_relay ipif System 
Bootp Relay Status                    :Disabled 
Bootp Hops Count Limit           :4 
bootp Relay Time Threshold    :0 
Interface         Server 1          Server 2           Server 3          Server 4  
-------------     ---------------     ----------------      ---------------        -------------- 
  System    10.48.74.122     10.23.12.34     10.12.34.12    10.48.75.121 
 
Total Entries: 1 
 
DES-3326SR:4#

 

Summary of Contents for DES-3326S - Switch - Stackable



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326S - Switch - Stackable

3Com 4210 Series Datasheet preview
4210 Series
Brand: 3Com Pages: 8
3Com PathBuilder S200 Series Feature Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 11
3Com 4400 Datasheet preview
4400
Brand: 3Com Pages: 8
3Com CoreBuilder 3500 Getting Started Manual preview
CoreBuilder 3500
Brand: 3Com Pages: 96
3Com 3C17539 Datasheet preview
3C17539
Brand: 3Com Pages: 12
3Com S7906E - Switch Datasheet preview
S7906E - Switch
Brand: 3Com Pages: 8
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Brand: Quintum Pages: 2
Belkin F5U307 User Manual preview
F5U307
Brand: Belkin Pages: 12
3Com Unified Gigabit Wireless PoE Switch 24... Quick Start Manual preview
Unified Gigabit Wireless PoE Switch 24...
Brand: 3Com Pages: 40
Eaton AGswitch Instructions Manual preview
AGswitch
Brand: Eaton Pages: 36
CYP OR-HD88HC Operation Manual preview
OR-HD88HC
Brand: CYP Pages: 20
Rockwell Automation Allen-Bradley 800F-ALR1 Installation Instructions preview
Allen-Bradley 800F-ALR1
Brand: Rockwell Automation Pages: 2
NBK EORP-200 Instruction Manual preview
EORP-200
Brand: NBK Pages: 32
CYP OR-44VWC Operation Manual preview
OR-44VWC
Brand: CYP Pages: 28
Contec SH-9008AT-POE Reference Manual preview
SH-9008AT-POE
Brand: Contec Pages: 38
Versitron SG70660M Installation Manual preview
SG70660M
Brand: Versitron Pages: 46
H3C S6890-54HF Installation, Quick Start preview
S6890-54HF
Brand: H3C Pages: 3
Popp POPE700397 Manual preview
POPE700397
Brand: Popp Pages: 9

Brands by name

Popular brands

Load more brands