background image

MODEL MQHAR

AssEMbLy MAnuAL

If you have problems or questions about your Creative Playthings play set,

DO nOT CALL THE RETAILER.

Contact Creative Playthings Customer service at 1-800-598-4997 or

[email protected]

Please  read  the  owner’s  manual  before  the 

assembly of your Play set. it provides additional 

information on the care and use of your Play set.

you must carefully read the entire instruction man-

ual before proceeding with the assembly or use 

of your new Play set.

Creative Playthings takes great care to design its 

products with your child’s safety in mind. How-

ever, only with careful supervision and proper 

safety instructions, can you be assured of safe 

play time on any product designed for children.

save these instructions for reference in case you 

need to contact customer service.

This product is intended for single 

family home/residential use only and 

not intended for use in any public 

setting. Placement in any public 

setting constitutes a misuse of this 

product.

All hardware on this set is specially coated 

for corrosion resistance.

If non-Creative Playthings hardware is used, 

it must be galvanized or stainless steel.

(Slide Not Included)

by

 

Creative Playthings®

Summary of Contents for FUNTIME swing sets





































Reviews: