Crane BevMAX Refresh 4 3800-4 Operation Manual Download Page 52

Page: 52 / 62

Page 52 of 62

SELECTION WILL NOT VEND

Loose

connections.

Defective

Plunger arm.

Defective

Harness.

Check Price, reset as needed.

Check Price, ensure credit is = to or

greater.

Selection will

not vend.

Vend Price set

incorrectly.

Insufficient

credit.

Check Gate & factory set up

recommendations for package.

Product & Gate

mismatch.

Move product away from Gate and use Test

Vend to check Gate operation. Check for bent

pins. Use small amount of WD-40 on pins and

recheck. Replace Gate as needed.

Clean, lubricate, check for flash,

replace Slide Assy.

Gate sticking.

Dirty / Worn

Tray Slide Assy.

Check Harness connections at VMC, Cup

Board, Port Board, X & Y Motor Boards, & X &

Y Motors.

Use Position Test to check Plunger arm,

replace Cup Assy. as necessary.

Cabinet

Control Board

Status Lights.

Check Cup Board, Port Board, X & Y Motor

Boards Green status lights are blinking. If only

one is On or Off, replace the Off Cabinet

Control Boards.

Replace Harness.

Summary of Contents for BevMAX Refresh 4 3800-4































































Search results

Summary of Contents for BevMAX Refresh 4 3800-4

Reviews:

Related manuals for BevMAX Refresh 4 3800-4

Brands by name

Popular brands

Crane BevMAX Refresh 4 3800-4, Operation Manual

Search results

Summary of Contents for BevMAX Refresh 4 3800-4

Reviews:

Related manuals for BevMAX Refresh 4 3800-4

Brands by name

Popular brands