Crane BevMAX Refresh 4 3800-4, Operation Manual

Page: 23 / 62

Page 23 of 62
“Test Relays” - RELAY TEST
This function allows you to test the relay electronic control of the compressor (“Compressor #”), the evaporator
fan(s) (“Fan #”), and the sign front light (“Light#”).
CAUTION: Disconnect power to the compressor before testing the compressor relay. Failure to disconnect
power to the compressor before testing the relay could result in damaging the compressor.
Press key number 4 and the display will show “Compressor #”, where # is the state of the relay - 0 = not activated
or off; 1 = activated or on. Press key number 4 to toggle the relay on and off. Press key number 2 to scroll to “Fan
#”, where # is the state of the relay - 0 = not activated or off, 1 = activated or on. Press key number 4 to toggle the
fan(s) on and off. Press key number 2 to scroll to “Light #”, where # is the state of the relay - 0 = not activated or
off; 1 = activated or on. Press key number 4 to toggle the lights on and off. Press key number 1 to return to “Test
Modes”. Press key number 2 to scroll to “Password Entry”.
* “Password Entry” - PASSWORD ROUTINE
This function allows you to enter the following routines which are not accessible until the operator enters a password,
which is set as 4-2-3-1. To enter the password, press key number 4 until the display goes blank. Then press key
number 2, then 3, then 1, and then 4, and “Cash Counters” should appear on the display. If not entered properly, the
display will return to “Password Entry” after approximately 16 seconds. If entered correctly, the display will go to the
next function “Cash”.
“Price Program” - PRICE SETTING ROUTINE
This function allows the user to set pricing. When Configuration Code 1 is programmed to “Config 1 0” the vender is
set for single price vending. When Configure Code 1 is set to “Config 1 1”, the vender is set for multi-pricing (or a
price for each selection needs to be set). Note: This routine is lockable when using a data collection device.
Single Price price setting:
Press key number 4 “Single Price” will show on display. Press the ”4” key and “Price Sel #.## will show on
display. Press key “2” to increase the vend price or key “3” to decrease the vend price. With the display showing
the vend price you require, press key “4” to save. All selections will be set to vend at the saved vend price.
Multiprice price setting:
Press key 4 and display will show “All Selections”. Press key 2 to scroll from “All Selections” to individual tray
selections “A, B, C, D, E”. With the display showing the All settings of the tray you wish to set price in press the
key 4 to enter. At “All Selections” when you press 4 and enter the display will show “#.##” or current price set.
Press key “2” to increase the vend price or key “3” to decrease the vend price. With the display showing the
vend price you require, press key “4” to save. If you select an individual tray letter to set price in, when you
press 4 and enter the display will show “All Selections (for tray A only)”. Press key 2 to scroll to A1 thru A9 then
back to All Selections (for A tray only)”. At the position you wish to set price when you press 4 and enter the
display will show “#.##” or current price set. Press key “2” to increase the vend price or key “3” to decrease the
vend price. With the display showing the vend price you require, press key “4” to save.
Factory default setting is “Single Price”. Press key number 1 to return to “Price Program”. Press key number 2 to
scroll to the next routine.
Price line setting:
This function will only display if Price Holding: On” is set. It will operate the same as setting prices except the
user will be prompted to set a price line rather than a price.