Crane BevMAX Refresh 4 3800-4 Operation Manual Download Page 53

Page: 53 / 62

Page 53 of 62

REFRIGERATION SYSTEM TROUBLESHOOTING FLOW CHARTS

ICE / FROST ON EVAPORATOR

CONDENSATE ON OUTSIDE OF PRODUCT DOOR

COMPRESSOR WILL NOT STOP

Clear Drain from Molded Evaporator

Box to the Condensate Pan.

Check Product Door seal & Harness

openings in Cabinet.

Ice / frost on

Evaporator.

Condensate Drain

plugged.

Air leak.

Move Machine.

Condensate on

outside of Product

Door.

Machine in direct

sunlight or near

heat source.

Machine in

location with

humidity above

70%.

Check Product Door seal &

Harness openings in Cabinet.

Air leak.

Verify Temp Sensor is plugged

in. Replace Temp. Sensor.

Compressor will

not stop.

Defective Cabinet

Control

Environmental

Board in AC

Distribution Box.

Replace Cabinet Control

Environmental Board.

Defective

Encapsulated

Temp. Sensor.

Summary of Contents for BevMAX Refresh 4 3800-4































































Search results

Summary of Contents for BevMAX Refresh 4 3800-4

Reviews:

Related manuals for BevMAX Refresh 4 3800-4

Brands by name

Popular brands

Crane BevMAX Refresh 4 3800-4, Operation Manual

Search results

Summary of Contents for BevMAX Refresh 4 3800-4

Reviews:

Related manuals for BevMAX Refresh 4 3800-4

Brands by name

Popular brands