background image

5

Craftmatic

®

  L-132 290-0001-b

advisory

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

important information

LOCkING CASTER 

          DETAIL

lock

Pacemaker warning

This product produces a vibrating sensation. 
It is possible that individuals with heart-assist 
pacemakers may experience a sensation similar to 
exercise. Consult physician for complete information. 

smaLL cHiLdren / Pets warning

After the base is unboxed, immediately dispose of 
packaging material as it can smother small children 
and pets. To avoid injury, children or pets should not 
be allowed to play under or on the base. Children 
should not operate this base without adult supervision.

HosPitaL use discLaimer

 

This base is designed for in-home use only.

 It is 

not approved for hospital use and does not comply 
with hospital standards. Do not use this base with 
tent type oxygen therapy equipment, or use near 
explosive gases.

service requirements

Service technicians are not responsible for moving 
furniture, removing headboards and footboards or any 
items required to perform maintenance on the base. In 
the event the technician is unable to perform service 
due to lack of accessibility, the service call will be 
billed to the purchaser and the service will have to be 
rescheduled.

Locking caster safety feature

 

Many adjustable bases are equipped with locking 
casters to prohibit the base from movement. For 
best results, place rubber caster cups under locking 
casters when the base is located on smooth or hard 
surface flooring—it is possible for locking caster 
equipped beds to slide without the use of rubber 
caster cups. 
To activate locking casters, push down on the lock 
tab. To disengage the locking mechanism, push up 
on the lock tab (see illustration).

fcc comPLiance

 

The equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection 
against harmful interference when the equipment 
is operated in a residential environment. This 
equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause 
harmful interference to radio communications. 
However, there is no guarantee that interference 
will not occur in a particular installation. If this 
equipment does cause harmful interference to radio 
or television reception, which can be determined 
by turning off the equipment off and on, the user is 
encouraged to try to correct the interference by one 
or more of the following measures: 
-   Reorient or relocate the receiving antenna
-   Increase the separation between the    

 

  equipment and receiver.
-   Connect the equipment into an outlet on a  

 

  circuit different from that to which the  

 

  receiver is connected.
-   Consult the dealer or an experienced radio/TV   
  technician for help.  

Radio Frequency = 433MHz.

Summary of Contents for L-132





























Reviews: