CPS FX1234 Service Manual Download Page 50 | Manualshive

Page: 50 / 57

CPS FX1234 Service Manual Download Page 50

50

4. HI Manifold Block PCB Lights

LV1, LV2, LV3 and LV4 Motor Lights (Red)

These lights are on monetarily when any of the LV1, LV2, LV3 or LV4 are

Required to either open or close. No more than one can be energized at any one time. Once
the valve has found it position, the Motor Light will de energize.

LS1 Solenoid Lights (Red)
                                                                        Will be energized when CHARGING is shown on LCD.
                                                                        Will be energized when FILTER CHANGE is shown on LCD.

LV1, LV2, LV3 and LV4 Sensor Lights (Red & Green)
                                                                         Red light will indicate CLOSED position.
                                                                         Green light will indicate OPEN position.

12VDC power supply connection

Green patch cord connection

HS1 Air purge solenoid valve 12 VDC

Red LED energized HS1solinoid is on is on

HV1 ball valve 12VDC

Red LED energized HV1 motor is on

HV2 ball valve 12VDC

Red LED energized HV2 motor is on

HV3 ball valve 12VDC

Red LED energized HV3 motor is on

Red LED HV3 closed

Green LED HV3 open

Red LED HV2 closed

Green LED HV2 open

Red LED HV1 closed

Green LED HV1 open

«
...
48
49
50
51
52
...
»

Summary of Contents for FX1234


























































Reviews:

No comments