manualshive.com logo in svg

CPS FX1234, Service Manual, Page: 32 / 57

Share
Download
CPS FX1234 Service Manual Download Page 32

 

32

 
 
 

 

 
2. Scale Replacement 

 

 

Disconnect power supply to the FX134A / FX1234 / FX3030 Series. 
 

 

j.

 

Remove back tank cover by removing both thumb screws holding cover on to main chassis. 

 
k.

 

 Remove tank strap from tank, and unplug heater blanket.  Then turn both ball valves on tank hoses to the off position, and 
disconnect tank hoses from purge block.  Then remove tank from scale platform and place to the side. 

 
l.

 

Remove two platform screws and set platform to the side.  Be sure to gather up spacer for reinstallation of platform. 

 
m.

 

Remove black scale patch cord, and the four screws on scale base to remove scale assembly. 

 
 
 
 

Unplug heater blanket 

 

 

 

         

        

 

 
 
 
 
 

              

           

                      

 
 
 
 
 
 

Remove thumb 
screw both sides 

Remove tank strap

Remove both platform screws 

Save spacer and unplug black 
patch cord. 

Remove mounting screws 
in all four corners. 

Summary of Contents for FX1234


























































Reviews:

No comments