manualshive.com logo in svg

CPS FX1234, Service Manual, Page: 33 / 57

Share
Download
CPS FX1234 Service Manual Download Page 33

 

33

 

3. Compressor Replacement 
 

Danger:

 

Only a qualified service technician should service this equipment. An Electrical Shock hazard is present 

which could lead to severe injury or even death. 
 

Disconnect power supply to 

FX134A / FX1234 / FX3030

 

series.  

 

 
Caution- all hoses may contain liquid refrigerant under pressure. Contact with refrigerant may cause frostbite or other 
related injuries. Wear proper personal protective equipment such as safety goggles and gloves. When disconnecting any 
hose, please use extreme caution. 
 
 
Danger: Always assume that high-pressure refrigerant exists in the Compressor. Failure to do so may result in bodily 
injury. 
 

a.

 

 Service Access: See Section 1  part 2 

 

b.

 

Disconnect power connector on compressor 

 

c.

 

Remove suction and discharge compressor hoses. 

 

d.

 

Remove the four mounting screws from bottom side of compressor shelf. 

 

             

 

 
 
 
 
 

 

 

Unplug power connector 

Remove both suction and discharge hoses 

Remove four mounting bolts from bottom 
side of compressor shelve 

Summary of Contents for FX1234


























































Reviews:

No comments