CPS FX1234 Service Manual Download Page 36 | Manualshive

Page: 36 / 57

CPS FX1234 Service Manual Download Page 36

36

6. Gauge Replacement

Danger- Avoid breathing refrigerant vapors and lubricant vapor or mist. Breathing high concentration levels may
cause heart arrhythmia, loss of consciousness, or even cause suffocation.

Caution- all hoses may contain liquid refrigerant under pressure. Contact with refrigerant may cause frostbite or other
related injuries. Wear proper personal protective equipment such as safety goggles and gloves. When disconnecting any
hose, please use extreme caution.

Caution- avoid breathing refrigerant vapors and/or lubricant mist. Exposure may irritate eyes, nose, throat, and skin.
Please read the manufacturers Material Safety Data Sheet for further safety information on refrigerants and
lubricants.

Danger: Always assume that high-pressure refrigerant exists. Failure to do so may result in bodily injury.

Disconnect power supply to the

FX134A / FX1234 / FX3030

Series.

a.

Run the RECOVER operation to remove residual refrigerant from the LO/HI Manifold gauges.

b.

Remove three screws from outer ring of gauge.

c.

Pull gauge from top panel, and remove nylon hose compression fitting from gauge.

d.

Install nylon hose compression fitting to new gauge and tighten.

e.

Reinstall gauge in top panel.

Remove three outer mounting screws

Loosen compression fitting with 5/16 wrench

«
...
34
35
36
37
38
...
»

Summary of Contents for FX1234


























































Reviews:

No comments