Cosel AME Series Manual Download Page 16

Page: 16 / 62

Applications manual

For AME series

︓

Read command

︓

Write command

:Returning a status of the PG alarm.

READ_LV_ALARM

:Returning a status of the LV alarm.

READ_PG_ALARM

TOTAL_OUTPUT_TIME_2

:Returning an accumulated operation time. (low 16 bits of hour)

:Returning an accumulated operation time. (minute)

TOTAL_INPUT_TIME_1

:Returning an accumulated time that the input voltage has been
applied. (minute)

TOTAL_INPUT_TIME_2

:Returning an accumulated time that the input voltage has been
applied. (low 16 bits of hour)

TOTAL_OUTPUT_TIME_3

:Returning an accumulated operation time. (high 16 bits of
hour)

TOTAL_INPUT_TIME_3

Table 6.1 Command outline (4/4)

6.8 State acquisition commands

READ_STOP_CODE

:Returning the code representing the halt condition.

:Returning an accumulated time that the input voltage has been
applied. (high 16 bits of hour)

TOTAL_OUTPUT_TIME_1

SYS_STORE_USER_SETTING

:Storing settings into the internal non-volatile memory.

6.9 Commands to set address, memory, and communication

SET_WRITE_PROTECT_ON

:Enabling a protection for the Write command.

SET_WRITE_PROTECT_OFF

:Disabling a protection for the Write command.

READ_SELECTION_CH

:Returning the selected slot for setting.

SET_SELECTION_CH

:Setting a selected slot.

READ_WRITE_PROTECT_PRM

:Returning a status of the protection for the Write command.

CTL_ACCUMULATE_MODE_OFF

:Disabling the accumulation mode.

READ_ACCUMULATE_MODE

:Returning a setting status of the accumulation mode.

SYS_RESTORE_FACTORY_SETTING

:Restoring a factory default for settings.

CTL_ACCUMULATE_MODE_ON

:Enabling the accumulation mode.

READ_STORE_USER_SETTING

:Returning a status of the stored setting in the internal non-
volatile memory.

SET_ADDRESS

:Setting a communication address.

READ_ADDRESS_PRM

:Returning a setting value of the communication address.

CTL_ACCUMULATE_EXEC

:Execution command in the accumulation mode.

CTL_ACCUMULATE_CLEAR

:Erasing buffer in the accumulation mode.

:Returning the lower four digits of the product lot number.

READ_ADDRESS

:Returning a communication address.

6.10 Commands to acquire product information

READ_SERIAL

:Returning the product serial number.

READ_IOUT_POINT

:Returning the decimal point position of the return value from
MON_IOUT command.

READ_VOUT_POINT

:Returning the decimal point position of the return value from
MON_VOUT command.

READ_RATED_VOUT

:Returning the rated voltage of the model.

READ_RATED_IOUT

:Returning the rated current of the model.

READ_VIN_POINT

:Returning the decimal point position of the return value from
MON_VIN command.

READ_PRODUCT_INFO

:Returning a information of output module.

READ_LOT_H

:Returning the upper three digits of the product lot number.

READ_LOT_L

READ_PR_ALARM

:Returning a status of the PR alarm.

ver1.1E 2020.2.12

Summary of Contents for AME Series































































Search results

Summary of Contents for AME Series

Reviews:

Related manuals for AME Series

Brands by name

Popular brands

Cosel AME Series, Manual

Search results

Summary of Contents for AME Series

Reviews:

Related manuals for AME Series

Brands by name

Popular brands