background image

 

 

 

 

© Corroventa Ltd. 

2017.02 

4 (15) 

 

Safety information 

This equipment can be used by children aged eight (8) years or above and people with reduced 
physical, sensory or mental capabilities or with lack of experience and knowledge provided they have 
been given instructions and information on how it is safely used and that they understand the 
hazards involved. 
 
Children must not be allowed to play with the equipment. Cleaning and maintenance must not be 
performed by children without SuperVision. 
 
Furthermore, the following warnings and instructions shall be read and observed: 
 

1.

 

The machine is intended for indoor use only. 

2.

 

The machine must be leveled when installed and operated. It must not be tilted more than 5 
degrees. 

3.

 

The machine must not be powered until the installation is finished in accordance with this 
manual. 

4.

 

The machine must not be covered as this can lead to overheating and fire hazard. 

5.

 

The machine must not be used as table, trestle, pallet or stool. 

6.

 

The machine must not be used to step or stand on. 

7.

 

Never use the machine without all filters installed as the particles, the dust and the water 
that escapes the machine will be released with the air and will also, on the way, damage the 
turbine. Ensure that the filters are clean as a cluttered filter inevitably stops or disturbs the 
drying process and can also cause the connected turbine to overheat. 

8.

 

The machine must not be used in spaces where explosive gases can be present. 

9.

 

Install the machine steadily and leveled so that it cannot fall over. 

10.

 

Keep children, animals and spectators away from the work place while installation is 
undertaken. 

11.

 

If the machine is broken, if the power connector or the cable is damaged, contact the retailer. 
Do not repair the equipment if you have not received specific training by the manufacturer. 

12.

 

Be careful not to damage the power cable. The cable must not go through water or pass 
sharp edges. 

13.

 

Never carry or tow the machine by its cable. 

14.

 

To use electrical equipment in humid or wet environment can be dangerous. Never power the 
machine if it is standing in water. 

15.

 

The machine must only be connected to grounded power outlet with 230VAC, 50Hz, max 16A. 

16.

 

A residual-current device / ground fault circuit interrupter should be used to minimize the 
risk of electric shocks. 

17.

 

Water must not come in contact with the electrical components of the machine. If this has 
happened, ensure that the equipment is dry before it is used again. 

18.

 

The power must always be disconnected before the machine is opened. 

19.

 

Repairs and maintenance of the electronics and the electrical system of the machine must 
only be made by qualified electrician. 

20.

 

Air hoses/pipes that are used and connected to the machine must be corrosion-resistant, 
able to withstand 80°C heat and have sufficient structural strength not to collapse or break 
from the underpressure generated by connected turbine. 

21.

 

The machine must never be used with any other accessories than those listed in this manual 
or those specifically approved by Corroventa Avfuktning AB. 

 
For further advice on product safety and use, please contact the supplier. 
 

Summary of Contents for WS4 ES



















Reviews: