manualshive.com logo in svg

Conviron ADAPTIS A1000, Installation, Operation & Maintenance Manual

The Conviron ADAPTIS A1000 is a state-of-the-art controlled environment chamber designed for precise plant growth. Ensure your investment remains optimal with our comprehensive Installation, Operation & Maintenance Manual. Easily download this essential manual for free from manualshive.com to ensure seamless setup, operation, and upkeep of your ADAPTIS A1000.

Share
Download
background image

 
 
 
 

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL 

 

 

February 2016 | 256574-ENG

 

R01     3-1 

 

3 

CHAMBER INSTALLATION REQUIREMENTS 

A1000 units must be placed in ventilated areas. The ideal temperature around the equipment is 
21ºC. Although it will perform at higher ambient temperatures, it is recommended that the product 
be placed in areas that have circulating air. 

3.1 Chamber 

Placement 

Conviron guarantees performance of the chamber for ambient temperature conditions between 
15°C and 30°C. It is important to ensure that the room in which the chamber is located adheres to 
these environmental conditions. 

A1000 products will dissipate up to 2400 W to ambient. 

 

 

3.1.1 Chamber 

Clearance 

  At least 1 ft. (300 mm) must be left clear behind the back wall. 

  At least 1 ft. (300 mm) must be left clear above the unit. 

  At least 2” (50 mm) must be left clear on each side of the A1000 when the PG Kit is 

installed. Note – if any kit other than the PG Kit is installed, no side clearance is 
required. 

3.1.2 Power 

Supply 

All A1000 products are single phase and delivered to the market with one of two options. 

 120VAC-1

-60 Hz – 2 wire plus ground – 20 Amp overcurrent protection 

 230VAC-1

-50Hz  - 2 wire plus ground – 16 Amp overcurrent protection 

 

This unit will tolerate ±10% voltage fluctuation from the rated voltage on the serial plate. A voltage 
stabilizer must be used if the fluctuation is greater than ±10%. Failure to do so can result in 
serious damage to the compressor and electronic components and will void warranty. 

Disconnect switch must be sized by a qualified, local electrician. 

 

Ensure at least 4” (100mm) of free space around the exterior side walls of a chamber 
with a PG kit to facilitate proper air circulation. Inadequate air circulation and cooling 
inside the chamber will result if this space is not provided. 

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brands by name

Popular brands

Load more brands