Conviron ADAPTIS A1000 Installation, Operation & Maintenance Manual Download Page 21 | Manualshive

Page: 21 / 64

background image

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL

February 2016 | 256574-ENG

R01 2-7

2.2.2.4 Installing the Lamp Support Canopies

The four lamp canopies are held in place by a full length bracket attached to the chamber wall.
Install the lamp canopy supports into the chamber wall slots, starting at the top of the chamber.

To install the lamp canopy supports:

1. Install the first lamp canopy support,

Item F, into the third and fourth set of
slots from the top of the chamber wall.
a. Install the support with the flat side

up by hooking the upper tab into
the third set of slots. The flat side
has an oval hole in it to locate the
canopy in position.

b. Press lightly on the bottom side

snapping it into the corresponding
slot approximately 1” (25 mm)
below the top one into the fourth
set of slots.

Figure 2-6

TC Lamp Canopy Supports Detail

2. Install the lamp canopy, Item G, onto the supports and gently push it into the chamber (Figure

2-6). Ensure the cable is on the right side of the chamber to connect it to receptacle. The
screw heads on the bottom of each side of the canopy will slip into the center hole of the
canopy support when the canopy is in the correct position.

3. Unscrew the receptacle protective cap below the canopy, insert the canopy connector, and

tighten to secure the connection.

4. Continue to install the remaining lamp canopies.

F

G

«
...
19
20
21
22
23
...
»

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brand: Thermo Electron Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands