Conviron ADAPTIS A1000 Installation, Operation & Maintenance Manual Download Page 20 | Manualshive

Page: 20 / 64

background image

Kit Installation

2-6 February 2016 | 256574-ENG

R01

2.2.2.3 Installing the Air Shelves

The air shelves connect to the back wall plenum to complete the internal air distribution system. It
is recommended to install the bottom shelf first.

To install the air shelves:

1. Tilt the front of the air shelf, Item D,

upwards and install the flange on the
back of the shelf into the lowest slot in
the back wall plenum, Item B.

2. Install the air shelf support clip, Item

E, into the corresponding slot in the
chamber wall and secure the clip to
the shelf with two (2) screws, Item C
(Figure 2-4). Repeat to install the clip
on the other side of the shelf. Tighten
the screws to full resistance.

Figure 2-4

TC Air Shelf Support Clip Installed

3. Secure the air shelf, Item D, to the

back wall plenum, Item B, with five (5)
screws, Item C (Figure 2-5).

4. Tighten the screws to full resistance.
5. Continue to install the remaining air

shelves.

Figure 2-5

TC Bottom Air Shelf Installed

Use a stubby Phillips screwdriver or a Phillips driver on a socket wrench to install the
screws into the support clip for the lowest shelf.

E

C

D

D

B

C

«
...
18
19
20
21
22
...
»

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands