Conviron ADAPTIS A1000 Installation, Operation & Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 64

background image

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL

February 2016 | 256574-ENG

R01 2-15

2.3.2.4 Installing the Back Wall Plenum

The back wall plenum directs airflow
down towards the Unifloor™.

To install the back wall plenum:

1. Remove the rubber instrumentation

port plug from the inside wall and
temporarily re-install it in the port on
the outside wall.

2. With the plenum handle at the top,

gently slide the back wall plenum,
Item B, into the chamber.

3. Position the plenum at a slight angle

to clear the protruding lamp
receptacles and the aspirator and
push it into place against the chamber
back wall.

4. Engage the locating pins above the

handle on the top of the plenum into
the holes in the top of the chamber.

5. Secure the plenum to the chamber

with twelve (12) screws, Item C
(Figure 2-16).
a. Install the eight (8) vertical screws

loosely to hold the plenum in
place.

b. Gently pry the back wall plenum

upwards to align the four (4)
bottom holes in the plenum with
the holes in the bottom support
and install the screws.

c. Tighten all screws to full

resistance.

Figure 2-16

PG Back Wall Plenum Installed

B

C

Aspirator

Rubber Plug

Lamp

Receptacles

«
...
27
28
29
30
31
...
»

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands