Conviron ADAPTIS A1000 Installation, Operation & Maintenance Manual Download | Manualshive

Page: 11 / 64

background image

A1000 INSTALLATION, OPERATION, & MAINTENANCE MANUAL

February 2016 | 256574-ENG

R01 1-1

1 PRECAUTIONS

The equipment is intended to be installed, operated, maintained, and serviced only by trained
personnel, according to the instructions and precautions described in the manuals provided by
Conviron.

The following precautions are intended to help guide users in the safe operation of Conviron
chambers.

1.1 Hazard Identification Symbols

The following symbols are used throughout this manual and/or on the equipment to draw your
attention to important warnings, guidelines and product information.

Table 1-1

Hazard Identification Symbols

Symbol Description

The “

HAZARD WARNING

” symbol is used whenever a hazard exists which

could cause personal injury or potential equipment damage, and requires
correct procedures/practices for prevention.

The “

IMPORTANT INFORMATION

” symbol is used to identify operating

procedures which must be followed to ensure smooth and efficient equipment
operation.

The “

ELECTROSTATIC DISCHARGE

” symbol is used to identify equipment

which is sensitive to electrostatic discharge.

The “

BURN HAZARD/HOT SURFACE

” symbol is used to identify surfaces

which are hot enough to cause personal injury.

The “

PROTECTIVE EARTH-GROUND-MANDATORY ACTION

” symbol is

used to identify the protective earth connection.

The “

PROTECTIVE EARTH-GROUND

” symbol is used to identify the

protective earth connection.

«
...
9
10
11
12
13
...
»

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brand: flowair Pages: 24

Brand: Conviron Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands