Conviron ADAPTIS A1000 Installation, Operation & Maintenance Manual Download Page 36 | Manualshive

Page: 36 / 64

background image

Kit Installation

2-22 February 2016 | 256574-ENG

R01

2.4.2.2 Installing the Back Wall Plenum

The back wall plenum closes the front of
the chamber plenum to distribute air
evenly throughout the chamber.

To install the back wall plenum:

1. Remove the rubber instrumentation

port plug from the inside wall and
temporarily re-install it in the port on
the outside wall.

2. With the plenum handle at the top and

the short flanges towards the back
wall, gently slide the back wall
plenum, Item B, into the chamber.

3. Position the plenum at a slight angle

to clear the protruding lamp
receptacles and the aspirator and
push it into place against the chamber
back wall.

4. Engage the locating pins on the top of

the plenum into the holes in the top of
the chamber.

5. Secure the plenum to the chamber

with twelve (12) screws, Item C
(Figure 2-25).
a. Install the eight (8) vertical screws

loosely to hold the plenum in
place.

b. Gently pry the back wall plenum

upwards to align the four (4)
bottom holes in the plenum with
the holes in the bottom support
and install the screws.

c. Tighten all screws to full

resistance.

Figure 2-25

IN Back Wall Plenum Installed

C

B

Aspirator

Rubber Plug

Lamp

Receptacles

«
...
34
35
36
37
38
...
»

Summary of Contents for ADAPTIS A1000

































































Reviews:

No comments

Related manuals for ADAPTIS A1000

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands