ConMed 1000 SES Service Manual Download Page 6

CAUTION - Before connecting,
read instructions.

TYPE CF EQUIPMENT CLASS 1

Protect against dripping water.

Alternating Current

1-2

• The CONMED 1000SES

TM

Filters are com-

pletely disposable. Please handle these dispos-
able filters according to your local codes or
regulations and hospital policy. These filters
may be disposed of or incinerated, whichever
is appropriate for your institution.

• The CONMED 1000SES

TM

Filter should be

changed according to the life of the filter. The
CONMED 1000SES

TM

Filter, used with the

CONMED 1000SES

TM

, should not be used

for more than 8 hours. Failure to change the
filter may result in decreased efficiency and
contamination of the electric motor, vacuum
pump, and sound absorbing media within the
unit.

• If fluid is expected to be aspirated by the
CONMED 1000SES

TM

Filter, fluid collection

devices must be installed with the vacuum
hose assembly. Failure to install a fluid collec-
tion device could cause filter blockage and
electrical damage.

WARNING: DO NOT OPERATE THIS
DEVICE IN THE PRESENCE OF FLAM-
MABLE ANESTHETIC GASES,
ENRICHED OXYGEN ATMOSPHERES
OR NITROUS OXIDE.

WARNING: REFER SERVICING TO
QUALIFIED BIOMEDICAL TECHNICAL
PERSONNEL.

There are no user serviceable components in
the CONMED 1000SES

TM

Smoke Evacuation

System. Refer service to qualified service per-
sonnel.

Use only with the AC cord provided and
always plug into a grounded outlet.

The CONMED 1000SES

TM

unit, filters and

accessories are not intended for contact with
patients.

CAUTIONS:

• Do not block either the tubing or the filter.
If either becomes occluded or significantly
restricted, the motor/blower may overheat and
cause the unit to fail.

• Using any other filter or accessory not sup-
plied by CONMED may cause damage to the
system and will void the warranty.

• Care must be exercised in the installation of
hoses, adapters and suction canisters. Failure
to follow the procedures outlined in this
manual may result in overheating of the motor
and may void the unit warranty.

• When using a Suction Canister set up, do
not increase the vacuum setting to more than
50%. Failure to observe this maximum may
result in overheating of the motor and system
failure.

DANGER - Risk of explosion if used
in the presence of flammable
anesthetics.

CAUTION - Grounding reliability can
only be achieved when the equipment is
connected to a receptacle marked
“Hospital Grade” or “Hospital Only”.

CAUTION - Electrical shock hazard.
Do not remove cover. Refer servicing to
qualified service personnel.

IPX1

1.4 Explanation of Symbols

60-6852-ENG (-).qxd  2/1/99  12:40 PM  Page 1-2

Summary of Contents for 1000 SES



























Reviews: