Condair TE Series Operation And Maintenance Manual Download Page 22 | Manualshive

Page: 22 / 44

background image

21

Maintenance

Condair TE

6

Maintenance

Regular maintenance of the humidifier is a requirement for maintaining the safety and operational

efficiency of the humidifier. Perform only those maintenance procedures described in this manual, and

follow all instructions closely. Use only original Condair replacement parts.

Personnel Qualifications

The Condair Ceiling Mounted Evaporative Humidifier must only be operated by personnel who are

adequately qualified, well trained and are authorized by the customer.

Safety

Certain operations of the Condair Ceiling Mounted Evaporative Humidifier may require the user to access

the control cabinet or plumbing cabinet, which may expose the user and equipment to the hazards

described in chapter

.

6.1

Inspecting the Humidifier

Ensure the humidifier is inspected before and after maintenance. Refer to the checklist below as a

starting point for your inspection.

Is the humidifier main unit level?

Is there any water leakage from the supply water piping?

Is the water supply service valve closed?

Is there any water leakage from the drain piping?

Does the drain piping have a sufficient downward gradient?

Is there any water leaks from inside the unit? (Open the cover to make an internal inspection.)

Is all electrical wiring correctly installed and secured?

Have all pins on the remote controller upper casing unit’s DIP switch been switched OFF?

Has the remote controller casing been replaced and closed again?

Is the humidifier power source’s leakage current circuit breaker turned to the OFF position?

Has the humidistat setting been returned to the preferred humidity level?

«
...
20
21
22
23
24
...
»

Summary of Contents for TE Series













































Reviews:

No comments

Related manuals for TE Series

23-11-2233N-006

Brand: Maytag Pages: 16

Brand: N'oveen Pages: 9

Brand: Daitsu Pages: 59

Brand: Sinclair Pages: 20

Brand: HIdRos Pages: 56

Brand: Qlima Pages: 220

Brand: Russell Hobbs Pages: 8

Brand: Oster Pages: 24

Brand: GeneralAire Pages: 12

Brand: Duronic Pages: 14

Brand: ECG Pages: 120

Brand: Ecoair Pages: 14

Brand: Cooper&Hunter Pages: 8

Brand: Cooper&Hunter Pages: 20

Brand: SereneLife Pages: 4

Brand: Rasonic Pages: 35

Brand: Goldstar Pages: 36

Brand: Goldstar Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands