background image

4

Introduction

Condair TE

  

Introduction

Thank you for purchasing the Condair Ceiling Mounted Evaporative Humidifier.
The Condair Ceiling Mounted Evaporative Humidifier incorporates the latest technical advances and 

meets recognized safety standards.
Improper use of the humidifier may result in danger to the user or third parties, and/or damage to property.
To ensure safe, proper, and efficient operation of the humidifier, please observe and comply with all 

information and safety instructions contained in this manual, as well as all relevant documentation of 

components of the installed humidification system.
If you have additional questions, please contact your Condair representative. They will be glad to assist 
you. 

1.1 

General

Limitations of the Manual

The subject of this manual is the Condair Ceiling Mounted Evaporative Humidifier in its different versions. 

The various options and accessories that are described in this manual pertain to the proper installation/

operation of the equipment. 
This  manual  is  restricted  to  the  operation  and  maintenance  of  the 

Condair  Ceiling  Mounted  Evaporative  Humidifier. This  manual  is  intended  for  competent  personnel 

suitably qualified for their respective tasks. The specifications are supplemented by various separate 

items of documentation (such as the parts list). Where necessary, appropriate cross-references are 

made to these publications in the specification.

Symbols Used in this Manual

CAUTION!

The word "CAUTION" in conjunction with the general caution symbol is used to provide safety 

instructions that, if neglected, may cause damage and/or malfunction of the unit or damage to 

property. 

WARNING!

The word "WARNING" in conjunction with the general warning symbol is used to provide safety 

instructions that, if neglected, may cause injury to personnel. Other specific warning symbols may 

also be used in place of the general symbol.

DANGER! 

The word "DANGER" in conjunction with the general danger symbol is used to provide safety 

instructions that, if neglected, may cause severe injury to personnel or even death. Other specific 

danger symbols may also be used in place of the general symbol.

Storage of Manual

Keep this manual in a place where it is safe and readily accessible. If the equipment is moved to another 

location, please ensure that it remains with the equipment.
If the manual is lost or misplaced, please contact Condair for a replacement.

Summary of Contents for TE Series













































Reviews: