manualshive.com logo in svg

CommScope SYSTIMAX iPatch Panel, Manager'S Manual

Share
Download
CommScope SYSTIMAX iPatch Panel Manager'S Manual Download Page 50

Guide:

 SYSTIMAX

®

 iPatch

®

 Panel Manager Guide

3–12

Responding to Messages

The following table describes the two messages that the iPatch Manager display 
may show while you are performing unguided patching activities. It includes 
instructions for responding to each message.

Important: 

When using the following table, make sure that the connection 

information shown on the iPatch Manager display is correct before pressing Yes. If 
the information is not correct, press Cancel. Then, press Confirm on the Ready 
screen and confirm the patch connection. See “Confirming Patch Connections” on 
page 4–3.

Table 3–1

Messages That May Be Shown During Unguided Patching Activities

If you see…

And you are…

You should…

Did you restore the 
connection?

a. Removing a connection.

You removed one end of a patch cord and realized 
it was the wrong cord. Then, you inserted that cord 
back into the same port.

a.

If the connection information shown is correct

, 

press Yes.

The iPatch Manager recognizes that the patch 
connection still exists.

b. Adding a connection. 

A port that you want to use is occupied. You 
removed one end of the patch cord to free the port 
and inserted the patch cord for the new 
connection.

b. Press No.

The iPatch Manager recognizes that you are 
adding a connection and asks you to connect the 
other end of the patch cord. The iPatch Manager 
also recognizes that one end of the original patch 
connection is unknown and needs to be confirmed.

Note: 

It is a good practice to completely remove a 

patch cord that is no longer needed.

Did you move one end of the 
connection?

a. Moving one end of a patch cord.

a.

If the connection information shown is correct

, 

press Yes.

The iPatch Manager recognizes that you moved a 
connection.

b. Adding a connection.

However, the display shows a connection that is 
different from the one you are adding.

b.

If you are starting a new connection

, press No.

The iPatch Manager recognizes that you are 
adding a new connection. After you have finished 
adding the connection, press Confirm on the 
Ready screen and confirm the patch connection. 
(See page 4–3.)

If you are not starting a new connection

, press 

Cancel.

Press Confirm on the Ready screen and confirm 
the patch connection. (See page 4–3.)

Summary of Contents for SYSTIMAX iPatch Panel
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands