Comdial DSU and DSU II System Reference Manual Download Page 17

Page: 17 / 136

Programmable Buttons

•

Allow you to store numbers for automatic dialing functions

•

Allow you to store telephone extension numbers for Direct Station
Selection (DSS)

•

Indicate which lines are either in use or on hold (green light)

Speaker

•

Sounds distant party’s voice

•

Sounds ringing and call progress tones

Shift Button

•

Allows access to autodial numbers programmed under DSS buttons

Speaker Button (SPEAKER)

•

Turns your speaker on or off

•

Disconnects a call when you are on a handsfree call

•

Ends or cancels programming

•

Activates group listen feature

TAP Button (must be preprogrammed for only one of the
following functions)

•

Recalls dial tone, or activates host system features

•

Retrieves held calls or last call placed on hold

Transfer/Conference Button (TRANSFER/CONFERENCE)

•

Transfers calls

•

Sets up conference calls

Volume Control

•

Regulates the volume of the ringer, the speaker, the handset, the
headset, and of the group listen feature

GCA70–245

Introducing The LCD Speakerphone

LCD Speakerphone Reference Manual 1–11

Summary of Contents for DSU and DSU II









































































































































Search results

Summary of Contents for DSU and DSU II

Reviews:

Related manuals for DSU and DSU II

Brands by name

Popular brands

Comdial DSU and DSU II, System Reference Manual

Search results

Summary of Contents for DSU and DSU II

Reviews:

Related manuals for DSU and DSU II

Brands by name

Popular brands