ComAp InteliLite MRS16 Manual Download Page 263

Page: 263 / 632

InteliLite Global Guide

263

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

DD/MM/YYYY [-]

Default value

1.1.2015

Alternative config

Step

[-]

Comm object

24553

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Always

Description

Actual date adjustment.

Date

back to List of setpoints

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

0 .. 240 [min]

Default value

60 min

Alternative config

Step

1 min

Comm object

8979

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Always

Description

Time interval for periodic history records.

Time Stamp Period

back to List of setpoints

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

Disabled / Winter / Summer / Winter - S / Summer - S [-]

Default value

Disabled

Alternative config

Step

[-]

Comm object

8727

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Always

Description

Behavior of switching between winter and summer time.

Disable

Automatic switching between summer and wintertime is disabled.

Winter

(Summer)

Automatic switching between summer and wintertime is enabled and it is set to winter

(summer) season.

Winter - S

(Summer - S)

Modification for southern hemisphere.

Summer Time Mode

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands