ComAp InteliLite MRS16 Manual Download Page 123

Page: 123 / 632

InteliLite Global Guide

123

start

Start the engine in MAN mode.

stop

Stop the engine in MAN mode.

fault reset

Acknowledging alarms and deactivating the horn output.

gcb close

Closing GCB in MAN and TEST mode.

gcb open

Opening GCB in MAN and TEST mode.

off

Switching to OFF mode.

man

Switching to MAN mode.

auto

Switching to AUTO mode.

status

Get status information from controller unit.

help

Get a list of available SMS requests.

Note:

Between commands are internal delays adjusted due to system requirements.

Example:

When the controller, in AUTO mode, with a controller name of “InteliLite-Test”, with the CM-

GPRS module and access code “0” receives the SMS:

0 man, start, gcb close, gcb open, stop, auto

Controller mode will be changed to MANUAL mode. The engine will be started and GCB will close. Then

GCB will open, the engine will stop and it will go into AUTO mode again.

The controller will send back the SMS (controller will respond to SMS after every command has been

finished, not sooner.):

#InteliLite-Test: <OK>,<OK>,<OK>, <OK>,<OK>, <OK>

The value <OK> or <ERROR> means if the command has been performed succesfuly or not.

Emails

Event Email

The InteliLite controller equipped with the CM-Ethernet communication module is able to send Event Email

according to the setting of setpoint:

Event Message (page 329)

Note:

Firstly setpoints

Email Address 1 (page 326)

and

SMTP Sender Address (page 320)

(for CM-GPRS) or

SMTP Sender Address (page 331)

(for CM-Ethernet) have to be adjusted.

Note:

Summer Time Mode (page 263)

and

Time Zone (page 328)

have to be adjusted for correct time in emails.

Message structure:

Controller

-----------------------------------------------

Name: XXX

Serial number: XXX

SW branch: XXX

SW version: XXX

Application: XXX

Appl. version: XXX

Date: dd/mm/yyyy

Time: hh:mm:ss

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands