ComAp InteliATS PWR Reference Manual Download

Page: 89 / 111

InteliATS

PWR, SW version 2.5, ©ComAp

– May 2015

IA-NT- PWR-2.5-Reference Guide.pdf

Remote Control and Data Logging

PC software

– LiteEdit

On the PC (for direct or modem connection) has to be

installed the ComAp’s software package

LiteEdit. (based on Windows 95 or newer platform)
LiteEdit enables:



read the quantities



adjust all set points



control the engine



configure the controller



select software configuration



modify alarm inputs and outputs



modify password, commands protections



direct, modem or Internet communication

Direct cable connection

An external communication module is necessary to enable direct cable connection to a PC. The
module is plugged into the slot located on the rear side of the controller. Find more information about

installation of the modules

in a separate chapter.

A RS232, USB or RS485 interface can be used for direct cable connection to a PC. The setpoint

COM1 Mode

COM2 Mode

(according to the interface used) must be set to DIRECT position for this

kind of connection.

RS232

CROSS-WIRED

RS232 CABLE

IL-NT RS232

IL-NT RS232-485

RS485

RS485 CABLE

IL-NT RS232-485

Physical COM Port

RS232

USB

CROSSED-WIRED

RS232 CABLE

IL-NT RS232

Virtual COM Port

USB

Shielded USB „A“

cable

IL-NT S-USB

Virtual COM Port

RS232

USB

IRECT CABLE CONNECTION TYPES

The following modules are available for direct connection to a PC:

1. IL-NT RS232
2. IL-NT RS232-485

IL-NT S-USB

(USB easily removable service module)

The RS232 or USB interface uses COM1 port of the controller. The RS485 uses COM2.

Summary of Contents for InteliATS PWR
















































































































Search results

Summary of Contents for InteliATS PWR

Reviews:

Related manuals for InteliATS PWR

Brands by name

Popular brands

ComAp InteliATS PWR, Reference Manual

Search results

Summary of Contents for InteliATS PWR

Reviews:

Related manuals for InteliATS PWR

Brands by name

Popular brands