ComAp InteliATS PWR Reference Manual Download | Manualshive

Page: 102 / 111

background image

InteliATS

NT

PWR, SW version 2.5, ©ComAp

– May 2015

102

IA-NT- PWR-2.5-Reference Guide.pdf

IL-NT-RD Remote display software

This chapter describes Remote display software IL-NT-RD, which is designed as an remote signaling
and control software for InteliATS

NT

, InteliLite

NT

and InteliDrive Lite controllers.

It is the optional

software which is possible to upload into controller i

nstead of standard controller’s firmware.

General description

Remote display software works as “remote display and control” for the master InteliATS

NT

, InteliLite

NT

or InteliDrive Lite controller. Genset/Engines can be controlled from remote display as well as from
master controller. All remote display screens (Measure, Setpoints and History) displays the same data
like master controller. Front panel buttons on both controllers work the same way. All remote display
LED’s shows the same state as corresponding LED’s on master controller.

Warning!

It is highly recommended to use the same type and model of controller for master and remote
display. Only in such case is assured the proper function of all buttons, LED diodes and
display.
Another combinations of HW types and models from Master controller and remote display are
not supported nor tested!

IL-NT-RD Software installation

The IL-NT-RD remote display firmware is installed in the same way as any other IA-NT firmware using
LiteEdit software. Please see LiteEdit Reference guide for details about upgrading firmware. IL-NT-RD
contains only firmware, not an archive.

However when there is IL-NT-RD firmware installed in the controller the procedure to install back the
original standard firmware is following:



Open any type of online connection.



DDE server will try to open the connection, but it will fail and write red error message in the
status bar.



At this moment go to

C

ONTROLLER

->

P

ROGRAMMING AND CLONING

->

P

ROGRAMMING

and select

proper!

firmware you want program to the controller. Choosing the wrong type of firmware

may result in non-functional controller.



Press "OK" button to program the firmware to the controller.

«
...
100
101
102
103
104
...
»

Summary of Contents for InteliATS PWR
















































































































Reviews:

No comments

Related manuals for InteliATS PWR

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: K&K Pages: 6

Brand: WAGNER Pages: 60

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: LLURIA Pages: 2

Wireless Blade FX Controller for Wii

Brand: Datel Pages: 2

Brand: Maximum Controls Pages: 58

E4KP ENTRYCHECK

Brand: SDC Pages: 6

Brand: Simpnic Pages: 16

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands