Coffee Queen CQube LF04 Maintenance Manual Download | Manualshive

Page: 42 / 58

background image

CQUBE SERIES

42

Filter mechanism

BREW CYCLE SETTING

Aeration

- Sum of sections from position 1 to 3 = 100%
- Adjustment in % (0-100%), applies to sections

from position 2 to 3

- Affects stirring in coffee bed > Taste:

Acidity

Pre brew

  - Pause at section between positions 1 and 3
  - Adjustment (0-25 sec) at step in 0.1 sec
   - Affects the amount of acid from stirring>

Taste: Acidity

Extraction

  - Pause between positions 2 and 4
  - Adjustment (0-25 sec) at step in 0.1 sec
  - Affects total contact time >   Taste: Body

Press time

- Sum of sections from position 3 to 5 = 100%
- Adjustment in % (0-100%), applies to sections

from position 3 to 4

- Affects the consistency of the grounds >

Cleanliness

- Affects the strain on plunger and cylinder >

Operating reliability: Vacuum pressure in cylinder

Decompress time

  - Pause between positions 3 and 5
  - Adjustment (0-25 sec) at step in 0.1 sec
   - Affects the consistency of the grounds >

Cleanliness

- Affects the strain on plunger and cylinder >

Operating reliability: Vacuum pressure in cylinder

Empty time

  - Pause between positions 5 and Home position
  - Adjustment (0-25 sec) at step in 0.1 sec
   - Affects the amount of finished coffee that

comes out of the cylinder

> Cleanliness / Operating reliability

2

Pre brew

3

Extraction

1

Home Position

5

Emptytime

4

Decompress

Brewing cycle settings

After Empty time the brewing continues until the micro switch is activated - Home position

«
...
40
41
42
43
44
...
»

Summary of Contents for CQube LF04



























































Reviews:

No comments

Related manuals for CQube LF04

Brand: Rangemaster Pages: 8

Brand: ID Technology Pages: 131

Brand: TAKE-A-LABEL Pages: 2

Brand: Wolfgang Puck Pages: 18

Brand: Bunn Pages: 6

Accents 162005EE

Brand: Morphy Richards Pages: 40

PerfectCoffee MC052

Brand: Waeco Pages: 168

Brand: Hamilton Beach Pages: 64

Brand: Scarlett Pages: 16

Prodigio TURMIX

Brand: Nespresso Pages: 60

Brand: Saeco Pages: 116

Brand: Hamilton Beach Pages: 24

Brand: SnackFood Pages: 6

jetStamp graphic 970

Brand: Reiner Pages: 94

Brand: Ginnys Pages: 6

Brand: GINNY’S Pages: 13

Stoelting CBB Series

Brand: Vollrath Pages: 21

FlavorPlus 840106700

Brand: Hamilton Beach Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands