manualshive.com logo in svg

Coffee Queen CQube LF04, Maintenance Manual

Share
Download
Coffee Queen CQube LF04 Maintenance Manual Download Page 15

CQUBE SERIES

15

IMPORTANT!

CLEANING PROGRAM

Detailed cleaning instructions

Clean brewer CQube SF MF LF

Cleaning of the 
brewing 
mechanism should 
be performed once 
a week.

  Insert technical service card

  Step to 

Clean Machine

 Press Enter 

 or press 

Clean Machine

 

Cleaning Hot Key

 appears on the display

  Open the machine door
   Put a container that holds at least 0.5 litres under the outlet for hot drinks. 

   Press  button 

 on the cleaning panel. (See fi g. A)

   Display  indicates: 

Place jug

Press ENTER to start

   Put 25gr (one portion) of cleaning agent (See fi g.B) in brewing mechanism.  

 Press 

Enter

 on the cleaning panel to start the cleaning process.

  Display indicates: 

Preparing Brewer 

Please Wait.

   Display  indicates: 

Cleaning Brewer

Time Left 300s

  The machine counts down from 

300 seconds. 

   Display  indicates: 

Rinsing Brewer

Cycles left 7

 

  Display indicates: 

Cleaning hot key

 when the cleaning is complete.

  Close the door and remove technical service card to return to normal mode. 

A

Fig.B

When the cleaning agent has been added, the process must not 
be interrupted but be allowed to run its course.

Note   

Total cleaning time 
about 10 minutes.
Filter cleaning agent 
is avalible from your 
dealer:
Product no. 
1104161

After cleaning of the 
brew mechanism is 
completed, dispense 
a cup of coffee and 
discard it to remove 
cleaning agent 
remains in the
fi lter and brew 
chamber.

Summary of Contents for CQube LF04



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands