manualshive.com logo in svg

Coffee Queen CQube LF04, Maintenance Manual

Share
Download
Coffee Queen CQube LF04 Maintenance Manual Download Page 49

CQUBE SERIES

49

ERROR CODE DESCRIPTION

Peripheral 

Hardware Error

This message will appear if you have loaded a faulty recipe 
into the machine, the IO-Board is broken and does not get 
connection with the UcMerisc board.
Usually this message appears if you eg. have loaded a stan-
dard recipe into a machine using pay system.
Make sure you are using the right recipe and reload.

Memory Error: 

Reload Recipes

There is no recipe loaded on the UcMersic board. Transfer 
of the recipes have been interrupted and not completed in 
UcLoader. Memory on the UcMersic board is broken. 

Fatal Error

Contact Service

Multiple Overcurrent messages at the same time, or 
shortcut on the IO-Board, try to run components in 
“Hardware Test” and locate faulty components, replace the 
IO-Board if no one is found.

Smartcard Error: 

Unknown Card

The smartcard is not programmed, chip on the smartcard 
is damaged, card reader is broken or broken cable between 
card reader and UcMerisc board.
Action: Insert and remove the card repeatedly, if the mes-
sage is shown every time, try another card. If the error 
remains replace the card reader.

Smartcard Error 

Wrong Pincode

Chip on the smart card have been damaged, replace card.

Pay Error

Type XXX

IO-Pay board is reporting error from the payment device, 
check coinchanger or cashflow device.

Summary of Contents for CQube LF04



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands