background image

9

Sweeping operation

  Operator panel

  (without overhead disposal)

  Vacuum operation

Vacuum  operation  helps  preventing
Dust  accumulation  when  sweeping.

•     Start the Ride-on-Sweeper
•     Switch on the Tipp switch for the suc-

    tion motor.

  

A  control  light  will  shine  on  the

    switch.  The  suction  operation
    begins.

     

Attention !

     

Do  not  switch  on  the  vacuum 

motor when cleaning wet areas/ wastes. 
It will cause damage to the vacuum motor.

—    To end the vacuum operation switch the
    Tipp  switch  to  Vacuum  motor  OFF.

 

Filter cleaning operation

The filter cleaning—vibration device pre-
vents  that  lamellas  of  the  filter  do  not 

clogg up with dust.

   Switch  off  the  vacuum  operation.

    Wait until the ventilator wheel stops
    and stands still.

Press the Tipp switch 5-10 seconds long 
for the filter cleaning.
The filter cleaning begins to work.

 

Switching off the Ride-on-Sweeper

•    Press the brake pedal

•     Secure  the  brake  by  pressing

    additionally  the  small  brake  pedal

    („hand-brake) 

into 

the 

latch.

  

If the brake is released afterwards,

    then the brake pedal must be kept

    pressed down.

•    Switch 

off 

all 

power 

supply

•     Lift  up  both  side  brushes  by  using

    both  levers  on  the  steering  column.

•    Latch  the  lifting  /  lower  level  for  the

    cylindrical brush.

•     Turn  the  key  into  position  0  =  OFF

    and take the key out.

    

 

Turn  the  battery  main  switch

     

OFF  and  take  it  out  of  the

     

holder.

     

Danger !

Inappropriate use of the Ride-on-Sweeper can 
lead  to  severe  injuries  to  persons  and  heavy 

damage to the equipment!
Prevent  unauthorized  persons  to  use  the 

Ride-on-Sweeper.
Never leave the operational Ride-on- Sweeper 

unsupervised.

Pull out the battery mains switch key and the 
key  of  the  ON/OFF  switch  when  leaving  the 

machine unattended.

(e.g. at the end of a job or days work the key 
should be removed)
Keep the Mains Switch key and ON/OFF key 

switch in separate places.

 KS 1100 - 

Englisch

Switch for the side brushes

1

0

ON

OFF

ON

OFF

ON

OFF

Switch for the cylindrical
brush

Switch for cylindrical
brush

Switch for

cylindrical brush

Battery charge-

status indication

Switch for

filter cleaning

ON and OFF key switch

Lever to open a flap and allow large

wastes enter

(Wastes till 65mm) E.g. small PET bottles,...

Summary of Contents for KS 1100 B





























Reviews: