background image

This warranty grants specific legal rights and shall be read in conformity with applicable state law.  In some jurisdictions, 

the applicable law mandates warranty provisions that provide greater legal rights than those provided for herein.  In such 

case, this limited warranty shall be read to include such mandated provisions; and any provision herein that is prohibited 

or unenforceable in any such jurisdiction shall, as to such jurisdiction, be ineffective to the extent of such prohibition or 

unenforceability without invalidating the remaining provisions and without affecting the validity or enforceability of such 

provision in any other jurisdiction(s).

TRADEMARKS 

The Clean Burn logo is a trademark of Clean Burn, LLC.  All other brand or product names mentioned are the registered 

trademarks or trademarks of their respective owners.

COPYRIGHT

Copyright © 2013 Clean Burn, LLC.  All rights reserved.  No part of this publication may be reproduced, or distributed 

without the prior written permission of Clean Burn, LLC. 4109 Capital Circle, Janesville, WI 53546.  Subject to change 

without notice. 

Warranty (continued)

Summary of Contents for CB-3500 series







































































































































Reviews: