– Press
»
«
.
– Use the
»
/
«
to select the video output.
– Press
»ENTER«
button 21 to confirm your selection.
– Use
»SETUP«
button 20 to leave the menu.
Setting and storing the radio stations
Switch on the device at the power switch
»POWER«
6.
Use
»TUNER«
28 or
»SOURCE«
button 13 to switch to
tuner mode and select the desired frequency band (FM or
AM).
FM
87,5 MHz – 108,00 MHz
AM
530KHz – 1710kHz
Keep one of the
»TUN-/TUN +«
buttons 24 pressed until
the frequency in display unit 10 automatically changes.
When a station is sufficiently strong, the search is
stopped and the station is simultaneously optimally set
and displayed.
To store the station, press »MEMO« button 42.
Set the desired channel position using the »STA/STA+«
button 23 or the numeric keys 19.
Re-press
»MEMO«
42 to confirm your entry.
To store additional programs, repeat the above steps.
Note:
– If, after pressing the MEMO button, no button is pres-
sed for 5 seconds then the device switches back to
the normal frequency display.
– You can set stations with a weaker signal by repeated-
ly pressing the »TUN-/TUN+ button 24.
Listening to radio:
Switch on the device at the power switch
»POWER«
6.
Use
»TUNER«
28 or
»SOURCE«
13 to switch to tuner
mode and select the desired frequency band (FM of AM).
The previously stored channel positions can be selected
using the numeric buttons 19 or the
»SRA-/STA+«
button
23 . Set non-stored stations using the
»TUN-/TUN+«
buttons 24.
The device switches between stereo and mono reception
when you repeatedly press
»ST/MO«
40. In case of bad
reception, we suggest that you switch to MONO.
If an RDS station is switched on then
appears in
display unit 10. By repeatedly pressing
»DISPLAY«
but-
ton 34, the device switches between
station names,
program type
and
transmission frequency
.
Inserting and removing a CD:
DVD Video CDs, Video-CDs, MP3-CDs and Audio-CDs
can be played back on this device. The device automati-
cally recognises the corresponding format after reading-in
the CD. Playable CDs are marked with one or more of the
following logos.
Switch on the DVD receiver and switch to DVD mode.
Then press
»OPEN/CLOSE«
9/38. The CD tray 8 is ope-
ned. Now insert the CD with the side to be played facing
downwards. The side to be played is blank. If both sides
are bland (e.g. in case of some DVD video CDs that are
recorded on both sides), then first play back the side that
is marked with A or a 1, depending on the CD. Single
CDs (8cm) without adapter can also be inserted.
Now close the CD tray by re-pressing
»OPEN/CLOSE«
9/38. The device immediately begins with play back.
Depending on the CD that is inserted, the device switches
to the highest pre-set AUDIO MODE. If no speakers are
connected to the device then playback may be without
sound, depending on the CD that has been inserted. To
listen to the CD via the television speaker you must
switch over to STEREO (in
SPEAKER SETUP PAGE
),
line
AUDIO MODE
).
(See »Setting the audio mode« page 47)
Warning!
To avoid damage to the device, no foreign objects must
enter the CD tray.
Note:
This DVD receiver supports the copy-protection
codes of most DVD video CDs and video CDs. This
means that the contents of these CDs can not normally
be copied by a video recorder onto tape during normal
playback.
37
TV DISPLAY
TV TYPE
VIDEO OUT
CVBS
ANGLE MARK
RGB
OSD LANG
YUV
AUDIO OUT
SCR SAVER
MAIN PAGE
- - GENERAL PAGE - -
SET PICTURE MODE
Sub
FR
FL
Stereo
MHz
RDS
PTY
Sub
FR
FL
Stereo
MHz
Memory
RDS
PTY
Sub
FR
FL
Stereo
RDS
PTY
SETUP MENU
SPEAKER SETUP
AUDIO MODE
DVD 534 HC - GB 25.06.2002 10:00 Uhr Seite 37
