Cisco TelePresence ISDN Link Administrator'S Manual Download Page 83

Page: 83 / 88

Cisco

TelePresence

ISDN

Link

Administrator

Guide

D14954.04 ISDN Link Administrator Guide IL1.1.2, MARCH 2015.

Mounting the unit

Wall mounting

If you want to mount the ISDN Link on a wall, follow the instructions below. Mount

the unit with the front panel facing up.

It is of great importance that the wall mount unit is safely installed, that the wall

is able to support the product and that the screws or mounting means used are

suitable for the wall and the weight of the product.

this type of equipment is to be installed by the submitter’s/dealer’s qualified

installer. Installer is responsible for obtaining safety inspection of the structural

integrity of the installation by the local authority/inspection department.

Table stand

Mount the four foot bumpers on its feet if you would like to place the ISDN Link on

a table.

Bottom view of the unit.

Front panel

facing up.

180 mm / 7.1 in

Connectors

facing down.

Contents

Introduction

Getting started

Software upgrade

Status information

System settings

Appendices

Summary of Contents for TelePresence ISDN Link

























































































Search results

Summary of Contents for TelePresence ISDN Link

Reviews:

Related manuals for TelePresence ISDN Link

Brands by name

Popular brands

Cisco TelePresence ISDN Link, Administrator'S Manual

Search results

Summary of Contents for TelePresence ISDN Link

Reviews:

Related manuals for TelePresence ISDN Link

Brands by name

Popular brands