manualshive.com logo in svg

Cisco CTS-SX10-K9, Getting Started Manual

Share
Download
Cisco CTS-SX10-K9 Getting Started Manual Download Page 8

Setup assistant

When you start the system for the first time, the Setup 

assitant runs automatically. 

Start the Setup assistant

Navigate to the upper left corner on the home screen and 

press 

OK

 on the remote control. 

Navigate to 

Settings

 and press 

OK

. Navigate to 

Setup 

assistant

 and press 

OK

. Follow the instructions on screen. 

If the system does not show a menu on screen:

• 

Make sure the monitor is connected and has been 

switched on.

• 

Make sure the remote control has batteries installed.

• 

Make sure the system is switched on.

If the system has just been switched on, wait a few minutes 

to allow the system to start up.

If there is still no menu on screen, make sure the monitor 

cable is connected to the video output connector. If in doubt, 

see the installation guide for your product.

On-screen display

D15117.01 SX10 Getting Started Guide TC7.1, MAY 2014.  

www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved. 

8

Cisco TelePresence SX10 Quick Set 

Getting Started Guide

Configuration

Back to task overview

Contents

Introduction

Configuration

Appendices

Contact

SX10 Quick Set

Summary of Contents for CTS-SX10-K9


























Reviews:

No comments

Brands by name

Popular brands

Load more brands