manualshive.com logo in svg

Cisco Catalyst Blade 3032, Software Configuration Manual

Share
Download
Cisco Catalyst Blade 3032 Software Configuration Manual Download Page 984

 

39-42

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-13270-06

Chapter 39      Configuring IP Unicast Routing

Configuring EIGRP

To create an EIGRP routing process, you must enable EIGRP and associate networks. EIGRP sends 
updates to the interfaces in the specified networks. If you do not specify an interface network, it is not 
advertised in any EIGRP update. 

If you have routers on your network that are configured for IGRP, and you want to change to EIGRP, you 
must designate transition routers configured with 

both

 IGRP and EIGRP. In these cases, perform Steps 

1 through 3 in the next section and also see the 

“Configuring Split Horizon” section on page 39-25

. You 

must use the same autonomous-system number for routes so that they are automatically redistributed.

EIGRP Nonstop Forwarding

The switch stack supports two levels of EIGRP nonstop forwarding:

•

EIGRP NSF Awareness, page 39-42

•

EIGRP NSF Capability, page 39-42

EIGRP NSF Awareness

The IP-services feature set supports EIGRP NSF awareness for IPv4. When the neighboring router is 
NSF-capable, the Layer 3 switch continues to forward packets from the neighboring router during the 
interval between the primary route processor in a router failure and the backup RP take-over, or while 
you manually reload the primary route processor for a nondisruptive software upgrade. 

This feature cannot be disabled. For more information on this feature, see the “EIGRP Nonstop 
Forwarding (NSF) Awareness” section of the 

Cisco IOS IP Routing Protocols Configuration Guide, 

Release 12.4

. 

EIGRP NSF Capability

Beginning with Cisco IOS Release 12.2(58)SE, the switch supports EIGRP Cisco NSF routing to speed 
up convergence and eliminate traffic loss following a stack master change. For details about this NSF 
capability, see the “Configuring Nonstop Forwarding” chapter in the 

High Availability Configuration 

Guide, Cisco IOS XE Release 3S

 at:

http://www.cisco.com/en/US/docs/ios/ios_xe/ha/configuration/guide/ha-nonstp_fwdg_xe.html#wp108
5061

The IP-services feature set also supports EIGRP NSF-capable routing for IPv4 for better convergence 
and lower traffic loss following a stack-master change. When an EIGRP NSF-capable stack master 
restarts or a new stack master starts and NSF restarts, the switch has no neighbors, and the topology table 
is empty. The switch must bring up the interfaces, re-acquire neighbors, and rebuild the topology and 
routing tables without interrupting the traffic directed to the switch stack. EIGRP peer routers maintain 
the routes learned from the new stack master and continue to forward traffic through the NSF restart 
process.

Traffic-share

Distributed proportionately to the ratios of the metrics.

Variance

1 (equal-cost load-balancing).

1.

NSF = nonstop forwarding

2.

EIGRP NSF awareness is enabled for IPv4 on switches running the IP services feature set.

Table 39-7

Default EIGRP Configuration (continued)

Feature

Default Setting

Summary of Contents for Catalyst Blade 3032





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands