manualshive.com logo in svg

Cisco 2000 Series, Configuration Manual

The Bosch 2000 Series Program Entry Manual is a comprehensive user manual that provides step-by-step instructions for configuring and operating the Bosch 2000 Series product. This essential manual is available for free download on our website, ensuring easy access for users to optimize their experience with this high-quality product.

Share
Download
background image

 

6-3

Cisco Wireless LAN Controller Configuration Guide

OL-1926-06OL-9141-03

Chapter 6      Configuring WLANsWireless Device Access

Configuring WLANs

Note

For release 4.0.206.0 and greater , the command format is expanded to allow support for multiple 
WLANs with the same SSID. To distinguish between the two WLANs, a unique profile name is 
added. The definition of the profile name is added to the command as follows: 

config wlan 

create

 

wlan_id profile_name ssid. 

If you do not specify an 

ssid

 the 

profile_name

 parameter is 

used for both the profile name and the SSID.

 

Refer to the 

“Configuring Multiple WLANs with 

the Same SSID” section on page 6-30

 for more details.

Note

When WLAN 1 is created in the configuration wizard, it is created in enabled mode; disable it 
until you have finished configuring it. When you create a new WLAN using the 

config wlan 

create

 command, it is created in disabled mode; leave it disabled until you have finished 

configuring it.

•

Enter 

config wlan disable

 

wlan-id

 to disable a WLAN, before making any modifications.

Note

If the management and AP-manager interfaces are mapped to the same port and are members of 
the same VLAN, you must disable the WLAN before making a port-mapping change to either 
interface. If the management and AP-manager interfaces are assigned to different VLANs, you 
do not need to disable the WLAN.

•

Enter 

config wlan enable

 

wlan-id 

to enable a WLAN.

•

Enter 

config wlan delete

 

wlan-id

 to delete a WLAN.

Activating WLANs

After you have completely configured your WLAN settings, enter 

config wlan enable

 

wlan-id

 to 

activate the WLAN.

Configuring DHCP

WLANs can be configured to use the same or different DHCP servers or no DHCP server. Two types of 
DHCP servers are available: internal and external.

Note

When using the Layer 3 LWAPP mode, you should configure the management and AP-manager 
interfaces to be on the same subnet so that access points can join the controller.

Internal DHCP Server

The controllers contain an internal DHCP server. This server is typically used in branch offices that do 
not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with 
the access points on the same IP subnet as the controller. The internal server provides DHCP addresses 
to wireless clients, direct-connect access points, appliance-mode access points on the management 
interface, and DHCP requests that are relayed from access points. Only lightweight access points are 
supported.

Summary of Contents for 2000 Series























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Series

Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Campbell CS225 Instruction Manual preview
CS225
Brand: Campbell Pages: 22
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Brand: HandyTrac Pages: 14
TA STA Quick Start Manual preview
STA
Brand: TA Pages: 6
HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Brand: Samson Pages: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Brand: Samson Pages: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Brand: Samson Pages: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Brand: Samson Pages: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Brand: X-POWER Pages: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Brand: Samson Pages: 80
Haehne DCX Quick Start Manual preview
DCX
Brand: Haehne Pages: 44
ZIMMERLI MESSTECHNIK LPS Series Operating Manual preview
LPS Series
Brand: ZIMMERLI MESSTECHNIK Pages: 12
H-Tronic TS 125 Manual preview
TS 125
Brand: H-Tronic Pages: 32
cinetto PS40.3 Assembly Instructions Manual preview
PS40.3
Brand: cinetto Pages: 56
Matelec FPC-36040 Owner'S Operation Manual preview
FPC-36040
Brand: Matelec Pages: 16
Bardiani Valvole BBZO BBZOG Instruction Manual preview
BBZO BBZOG
Brand: Bardiani Valvole Pages: 24
Jeckson Electric 47-1010A-T Owner'S Manual preview
47-1010A-T
Brand: Jeckson Electric Pages: 2

Brands by name

Popular brands

Load more brands