CIRRUS DESIGN SR20 Pilot Operating Handbook Download | Manualshive

Page: 419 / 508

background image

P/N 11934-S22

9 of 10

Cirrus Design

Section 9

SR20

Supplements

Frequencies. North American and International databases are
available. Database information is provided on a card that can be
inserted into the card slot on the GPS unit. Subscription information is
provided in a subscription packet provided with each system.

Navigation (Nav) Receiver

The Garmin GNS 430 provides an integrated Navigation (NAV)
receiver with VHF Omnirange/Localizer (VOR/LOC) and Glideslope
(G/S) capability. The VOR/LOC receiver receives on a frequency
range from 108.000 Mhz to 117.950 Mhz with 50 kHz spacing.
Glideslope is received from 329.150 to 335.00 in 150 kHz steps. The
Nav receiver controls are integrated into the Garmin GNS 430 control
mounted in the center console. The receiver control provides active
and standby frequency indication, frequency memory storage, and
knob-operated frequency selection. IDENT audio output for VOR and
LOC is provided to the audio system. The Nav antenna is mounted on
top of the vertical tail. 28 VDC for navigation receiver operation is
controlled through the Avionics Master Switch on the bolster switch
panel and supplied through the 5-amp GPS 1 circuit breaker on the
Avionics Essential Bus. The airplane is equipped with a Garmin GNS
430 integrated GPS Navigator, Navigation (NAV) receiver with VHF
Omnirange/Localizer (VOR/LOC) and Glideslope receiver.

Communication (COM) Transceiver

The GNS 430 includes a digitally-tuned integrated VHF
communications (COM) transceiver. The transceiver and integrated
controls are mounted in the Garmin GNS 430 unit. The transceiver
receives all narrow- and wide-band VHF communication
transmissions transmitted within a frequency range of 118.000 MHz to
136.975 MHz in 25.0 kHz steps (720 channels). For European
operations, the COM can be operator configured for 8.33 kHz channel
spacing (2280 channels). The tuning controls are collocated with the
NAV at the left side of the GNS 430 front panel. Frequency tuning is
accomplished by rotating the large and small concentric knobs to
select a standby frequency and then transferring the frequency to the
active window. The COM frequency display window is at the upper left
corner of the GNS 430 display. Auto-tuning can be accomplished by
entering a frequency from a menu. The COM 1 antenna is located
above the cabin on the airplane centerline. 28 VDC for transceiver

Revision 1: 05-25-05

«
...
417
418
419
420
421
...
»

Summary of Contents for SR20





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SR20

Brand: P&M Aviation Pages: 54

Brand: MAULE Pages: 29

Brand: Dudek Pages: 29

Universal 1.1 23

Brand: Dudek Pages: 48

Cabrio Synthesis

Brand: Dudek Pages: 44

Brand: InVento Pages: 2

Brand: North Wing Pages: 80

Brand: Parachutes de France Pages: 72

Brand: Sky Country Pages: 24

ALUULA G Series

Brand: Ocean Rodeo Pages: 4

Elite Models Drifter Plus

Brand: Value Hobby Pages: 11

Brand: PAPILLON Pages: 22

Brand: Rans Pages: 319

Brand: Eclipse Aviation Pages: 88

Brand: Schildkröt Pages: 32

Decathlon 8KCAB

Brand: Bellanca Pages: 178

Ultralight Flying Object 18"

Brand: Air Design Pages: 80

Brand: Air Design Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands